If you are using step recording method 1 to
record
☞ Proceed to “Recording Notes One by One (Step
Recording 1).”
If you are using step recording method 2 to
record
☞ Proceed to “Recording Individual Notes to Grid
Locations (Step Recording 2)” (p. 134).
Recording Notes One by One
(Step Recording 1)
5. Press [REC] to begin recording.
The [REC] indicator will light.
The following display will appear.
fig.8-26TEXT
6. Before inputting notes, select the Step Time,
Velocity, and Gate Time Ratio.
Use PAGE [<] [>] to move the cursor to the location of
the parameter that you wish to set, and use [INC]
[DEC] or the [VALUE] dial to set the value.
fig.8-27
Step Time
Select the length of the note that will be input (the
duration from when a key is pressed until the next key
is pressed).
Range:
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
The Step Time for a quarter note is 96.
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
Velocity
Specifies the strength of the note.
Range: REAL, 1–127
If you wish to input the velocity at which the note was
actually played, select “REAL.” If you wish to input a
fixed velocity value, specify the desired value of 1–127.
* During recording, the setting of “Changing the Loudness
of Notes Played on the Keyboard (Keyboard Velocity)” (p.
163) is ignored.
Gate Time Ratio
Specifies the time from when the key is pressed until it
is released (Gate Time), as a proportion of the Step
Time. Lower settings of this value will produce shorter
notes, and higher settings will produce longer notes.
Range: 1–200%
Normally, you should select a setting of about 80%.
Select 50% for staccato notes, and 100% for tenuto
notes.
* When the Rhythm part is the recording part, gate time
will be input with a fixed value, so it is unnecessary to
specify the gate time ratio.
7. Play the keyboard to input notes.
fig.8-31 (#MC fig.10-34)
Notes will be input when you release the key, and you
will then be ready to input the next note.
Each time you input a note, the input location will
advance by the length of the Step Time.
8. Repeat steps 6 and 7 to input the notes.
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
The Step Time, Gate Time Ratio and Velocity settings
of the previously input note are remembered. If you
wish to use the same settings for the next note, there is
no need to change the values of these parameters.
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
* In Step Recording 1, notes are always overwritten
(replaced) when they are recorded, meaning that if you
input notes in a part that already contained notes, the pre-
viously recorded notes will be erased.
9. When you finish inputting notes, press
[STOP/PLAY].
The pattern you recorded will be in the temporary pat-
tern (TMP). If you are happy with the pattern that you
recorded, use the Pattern Write operation to save it as
a user pattern.
To Next Page
Loading...
