Erasing Unwanted Data While
You Record (Real-Time Erase)
Real-Time Erase is a function that lets you erase only
the unwanted data that you specify a certain key or
range of keys during real-time recording.
In particular, this is convenient when you are record-
ing the rhythm part, since you can erase a specific
rhythm tone.
1. During recording, hold down [SHIFT] and
press [ERASE].
You will enter Real-Time Erase mode, and the follow-
ing display will appear.
fig.8-20 (#MC fig.10-22)
2. Use [INC] [DEC] or the [VALUE] dial to select
the type of data that you wish to erase.
Range:
ALL: All musical data in the recording part
will be erased.
NOTE: Notes in the specified range will be
erased.
PC: Program changes will be erased.
CC: All control changes will be erased.
BEND: Pitch bend will be erased.
P-AFT: Polyphonic aftertouch will be erased.
C-AFT: Channel aftertouch will be erased.
SYS-EX: System exclusive messages will be
erased.
TEMPO: Tempo data will be erased.
MUTE: Mute data will be erased.
CC#0–CC#127: Control changes of the selected con-
troller number will be erased.
* If you select CC#1, you can erase Modulation lever data.
For knob settings, you can also operate the corre-
sponding front panel knob to select that data (control
change) for erasure.
fig.8-21
The following knobs settings can be selected.
•Pitch (p. 57, p. 87)
[FINE TUNE]
•Pitch Envelope (p. 58, p. 87)
[ATTACK] [DECAY] [SUSTAIN] [RELEASE]
[DEPTH]
•Filter (p. 61, p. 90)
[CUTOFF] [RESONANCE]
•Filter Envelope (p. 63, p. 91)
[ATTACK] [DECAY] [SUSTAIN] [RELEASE]
[DEPTH]
•Amplifier (p. 67, p. 94)
[LEVEL] [PANPOT]
•Amplifier Envelope (p. 68, p. 95)
[ATTACK] [DECAY] [SUSTAIN] [RELEASE]
•LFO1 (p. 71)
[RATE] [FADE TIME] [PITCH DEPTH] [FILTER
DEPTH] [AMP DEPTH]
•Portamento (p. 77)
[PORTA TIME]
•Part Mixer (p. 33)
[LEVEL] [PANPOT] [KEY SHIFT] [REVERB] [DELAY]
[M-FX SW]
* [LEVEL]–[M-FX SW] can be selected by operating the
knobs in the Part Mixer page. At this time, this action
will only select the parameter; the value of the selected
parameter will not change.
3. Press [REC] to erase the unwanted data.
The specified data will be erased while you press the button.
* When “SYS-EX,” “TEMPO” or “MUTE” are selected,
the data will be erased from the [MUTE CTRL] part
regardless of the recording part.
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
If you select “NOTE” as the data to be erased, you can
press the key to erase only the specified note mes-
sages. Notes will be erased while you press the key-
board.
If you wish to erase notes of a specific range, press
keys to indicate the top and bottom of the range.
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
4. When you have finished, press [EXIT] to
return to normal recording mode.
To Next Page
Loading...
