96
Chapter 8. Trigger Settings for Each Pad [TRIGGER]
Here’s how to make trigger settings to ensure that the trigger
signals from the pads and pedals are appropriately conveyed
to the sound generator section.
If you specify the model (type) of pad that is connected to
each trigger input jack, the settings suitable for each pad will
be made. To specify the pad type, use the [TRIGGER] button
[F1 (BANK)].
If you want to make additional fine adjustments for each pad
to further adjust the sensitivity etc., you can use the [F2
(BASIC)] or [F5 (ADVANCE)] button to do so.
To ensure that the signals from the pads can be processed
appropriately by the TD-20X, you must specify the type of
pad you’re using (the trigger type) for each trigger input.
Trigger Type
A trigger type is a group of trigger settings with values
optimally adjusted for a particular pad.
In order to make the most suitable settings for the pad
connected to each trigger input, specify the model (type) of
the pad that is connected.
Only when factors unrelated to the selection of the proper
trigger type prevent you from getting good results in
performance should you fine-tune the individual parameters
for the pad you are using.
Trigger Bank
Trigger Banks allow you to store the 15 trigger settings as a
single unit of information. The large number at the left edge
of the above display is the Trigger Bank number. Move the
cursor to this area to select the Trigger Bank.
1.
Press the [TRIGGER] button.
The [TRIGGER] button lights.
2.
Press the [F1 (BANK)] button.
The “TRIGGER BANK” screen will appear.
fig.08-001-bank.eps_70
3.
Press the [CURSOR (left)] button to move the cursor
to the trigger bank number.
4.
Use the [-] [+] buttons or the [VALUE] dial to select
the Trigger Bank.
5.
Press the [CURSOR (right)] button to move the
cursor to a trigger type.
6.
Select the pad for which you want to make settings.
Strike the pad, or use the TRIG SELECT buttons to select it.
You can also use the [CURSOR] buttons to select the pad.
7.
Use the [-] [+] buttons or the [VALUE] dial to select
the trigger type.
Selecting the Pad Type
[F1 (BANK)]
Trigger bank number
Trigger Type
Used Modes
Trigger
Type
Rim
Shot
Positional
Sensing
Choke
play
Head Rim
KD-140
KD140
✕
✕ ✕ ✕
KD-120
KD120
✕
✕ ✕ ✕
KD-85
KD-80
KD85
✕
✕ ✕ ✕
KD-8
KD8
✕
✕ ✕ ✕
KD-7
KD7
✕
✕ ✕ ✕
PD-125X
PD-125XS
PD-125
PD125X
❍
❍ ❍ ✕
PD-120
PD120
❍
❍ ✕ ✕
PD-105X
PD-105
PD-100
PD105X
❍
❍ ❍ ✕
PD-85
PD-80R
PD-80
PD85
❍
❍ ❍ ✕
PDX-8
PDX8
❍
✕ ✕ ✕
PD-9
PD9
❍
❍ ✕ ❍
PD-8
PD8
❍
❍ ✕ ❍
PD-7
PD7
❍ ❍ ✕ ❍
CY-15R
CY15R
❍
❍ ✕ ❍
CY-14C
CY14C
❍
❍ ✕ ❍
CY-12R/C
CY12RC
❍
❍ ✕ ❍
CY-8
CY8
❍
✕ ✕ ❍
CY-5
CY-6
CY5/6
❍
✕ ✕ ❍
CY-12H
CY12H
❍
✕ ✕ ❍
VH-12
VH12
❍
✕ ✕ ❍
VH-11
VH11
❍ ✕ ✕ ❍
Non-Roland
pad
PAD1
❍
✕ ✕ ❍
Non-Roland
pad
PAD2
❍
✕ ✕ ✕
RT-10K
RT10K
✕
✕ ✕ ✕
RT-10S
RT10S
❍
✕ ✕ ✕
RT-10T
RT10T
✕
✕ ✕ ✕
TD-20X_e.book 96 ページ ２００９年６月８日 月曜日 午後３時５０分
To Next Page
Loading...
