Sanyo PLC-XM100L User Manual

51
Setting
Language English
Menu position
Input button Mode 1
Display On
Background Blue
Logo
Lamp control
Filter control
Fan control Normal
Simple mode On
Remote control Mode 1
RC sensor Back
Power management Off
Setting Menu
Press the MENU button to display the On-Screen Menu.
3UHVVWKH3RLQWŸźEXWWRQVWRVHOHFWSetting and press the
3RLQWŹRUWKH6(/(&7EXWWRQWRDFFHVVWKHVXEPHQXLWHPV
1
2
8VHWKH3RLQWŸźEXWWRQVWRVHOHFWWKHGHVLUHGLWHPDQG
WKHQSUHVVWKH3RLQWŹRUWKH6(/(&7EXWWRQWRDFFHVVWKH
selected item.
This projector has a Setting menu that allows you to set up the
other various functions described below.
3
8VHWKH3RLQWŸźEXWWRQVWRVHOHFWWKHGHVLUHGLWHPDQG
then press the SELECT button.
The language used in the On-Screen Menu is available in English,
German, French, Italian, Spanish, Portuguese, Dutch, Swedish,
Russian, Chinese, Korean and Japanese.
Language
This function is used to change the position of the On-Screen Menu.
Select Menu position and press the SELECT button. The Menu
position screen appears.
The Menu position changes each time you press the SELECT button
as follows.
the top left Æ the top right Æ the center Æ the bottom left Æ the
bottom right Æthe top left Æ.....
This function detects the input signal automatically. When a signal is
IRXQGWKHVHDUFKZLOOVWRS8VHWKH3RLQWŸźEXWWRQVWRVHOHFWRQH
of the following options.
Mode 1......Input search will not work.
Mode 2
......Input search works under the following situation:
– When pressing the INPUT button on the side control.
or the remote control.
Mode 3
......Input search works under the following situation:
– When turning on the projector by pressing the ON/
STAND-BY button on the side control or pressing the
ON button on the remote control.
– When pressing the INPUT button on the remote
control or on the side control.
- When no signal is detected.
3Note:
•While Input button is set to Mode 3, and no signal is
detected, if the Shutter or Freeze function is active, cancel
it to activate the Input search.
•While Input button is set to Mode 1 or Mode 2, the status
of Input and Lamp are displayed every time the signal is
switched.
•Only the last selected input source can be detected.
•If the INPUT, INPUT 1, INPUT 2, INPUT 3, ON / STAND-
BY or MENU button is pressed during Input search is
in progress, Input search will stop and go back to the
previous input signal.
Setting
Language
Menu position
Input button

Sanyo PLC-XM100L Specifications

General

Vertical scan range	48 - 100 Hz
Horizontal scan range	15 - 100 kHz
Projection technology	LCD
Contrast ratio (typical)	1000:1
Projector native resolution	XGA (1024x768)
Lamp type	NSH
Lamp power	330 W
Light source type	Lamp
Service life of light source	2000 h
Service life of light source (economic mode)	3000 h
Analog signal format system	NTSC, PAL, SECAM
S-Video inputs quantity	1
Dimensions (WxDxH)	489.5 x 371.1 x 164 mm
Noise level	38 dB
Power consumption (standby)	0.6 W
Power consumption (typical)	400 W
Power consumption (economy mode)	338 W

Weight and Dimensions

Weight	8900 g