SharkRF openSPOT2 - NXDN Settings; P25 Settings

description,orattheControlcallssection.
CrossmodegroupcallDTMFcode:ifaconnectorisactivewhichsupportsgroupcallsandC4FMcrossmode,
thenthiscodecanbeusedtostartgroupcallstotheIDenteredafterthiscode.
IfTransmitRXconfirmationischecked,thentheopenSPOT2willtransmitashortcallconfirmationafterthe
PTTisreleasedontheC4FMradio.
Defaultcallsignforcrossmodecalls:thiscallsignwillbeusedonC4FMnetworksforcallscomingfroma
radiowhichdoesnothaveacallsign(ex.DMR,NXDNID)insteadofusingtheIDsascallsigns.
Notethatiftheincomingcall'stalkeraliasisdecoded,thenitwillbeusedinsteadofthisdefaultcallsign
setting.
IfacallisreceivedbythemodemtotheEchoDGID,thentheopenSPOT2'sbuilt-inlocalechoservicegets
activated.Itwillrecordthecallandplaysitbackafterthecallisfinished.
IftheOnlyreceiveDGIDfrommodemcheckboxischecked,thencallsonlytothespecifiedDGIDfrom
modemwillbeprocessedbythemodem.
IftheReplaceDGIDtomodemenabledcheckboxischecked,thentheDGIDinallframesreceivedfromthe
networkwillbereplacedwiththespecifiedReplaceDGIDtomodemvalue.
IftheReplaceDGIDtonetenabledcheckboxischecked,thentheDGIDinallframesreceivedfromthe
modemwillbereplacedwiththespecifiedReplaceDGIDtonetvalue.
NXDNsettings
ThemodemwillonlyprocessNXDNcallswithamatchingRadioAccessNumberifitissetotherthan0.
IfacalliscomingfromamodewhichdoesnothaveIDinformation(ex.C4FM),orthesourceIDisoutside
theNXDNIDrange(0-65535),thentheDefaultcrossmodesourceIDwillbeusedasthesourceIDforthe
call.ThisIDwillalwaysbeusediftheAlwaysusethisIDincrossmodecheckboxischecked.
Ifyouuseanon-NXDNnetworkwithyourNXDNradio,youcansetthistoyourNXDNID.
IfAdvancedmodeisenabled,thefollowingsettingsshowup:
IfacallisreceivedbythemodemtotheEchoID,thentheopenSPOT2'sbuilt-inlocalechoservicegets
activated.Itwillrecordthecallandplaysitbackafterthecallisfinished.Bothprivateandgroupcallsare
answeredwithaprivateechocallreply.
IfacalliscomingfromamodewhichdoesnothaveIDinformation(ex.C4FM),orthedestinationIDis
outsidetheNXDNIDrange(0-65535),thentheDefaultcrossmodedestinationIDwillbeusedasthe
destinationIDforthecall.ThisIDwillalwaysbeusediftheAlwaysusethisIDincrossmodecheckboxis
checked.
IftheAllowonlyIDsascrossmodecallsignssettingisenabled,andthesourcecallsignofacrossmodecall
hasnoassociatedIDinthedatabase,andalsoitcan'tbeparsedintoanNXDNID,thenthecallwillbe
ignored.
P25settings
Settingspage
52