Home
SIEB & MEYER
Controller
CNC 61.00
SIEB & MEYER CNC 61.00 User Manual
5
of 1
of 1 rating
101 pages
Give review
Manual
Specs
To Next Page
To Next Page
Loading...
:
CNC 61.
00
Hardwar
e Descr
iption CNC 06
10510/1
2
Title
CNC 61.00
CNC 0610510/12
Hardware Description
SIEB & MEYER AG
Auf dem Schmaar
kamp 21 * D-21339 Lüneburg *
(Germany)
Telephone +049 - 4131
- 203 - 0 * Telefax: +049 - 4131 - 2
03 - 2000
E-Mail: documentation@sieb-me
yer.de
Internet:
http
://www.
sieb-
meyer.c
om
2
Table of Contents
Default Chapter
3
Table of Contents
3
1 Symbols
7
2 Safety Instruction and Application Advice
9
General Information
9
Appropriate Use
10
Transport and Storage
10
Installation
11
Electrical Connection
11
Operation
12
Maintenance
12
Disposal
12
Guarantee
13
3 Unit Assembly Complying EMC
15
Emission of Line and Field Interferences According to Category C3
15
4 General Information
17
5 Automation System CNC 61.00
19
Hardware Design
19
Programming
20
Performance Features
20
View of the Device 0610510
22
View of the Device 0610512
23
6 Dimensions
25
Module Type 0610510
25
Module Type 0610512
26
Connections for Module Type 0610510
27
Connections for Module Type 0610512
28
Type Plate
30
Module Designation
32
7 Technical Data
33
Supply Voltage 230 VAC
33
Supply Voltage 400 VAC
35
8 Functional Description of the Connectors/Interfaces
37
Front Panel 0610512
37
Pin Assignment and Interfaces
40
General Information
40
X1 - Connection of Motor Measuring System (Feedback)
40
Resolver Evaluation
41
Hall Effect Sensor Evaluation
42
Optical or Magnetical Length Measuring System
43
X2 - COM, Connection for Terminal or Programming Device
44
X3 - ENCO, Angle Pulse Output/Ssi
44
Angle Pulse Inputs
45
X4 - ENC1, Angle Pulse Input
45
X5 - ENC2 - Angle Pulse Input/Ssi
45
X6 - SIO, I/O Expansion
46
Connection to the Bus System
46
X7 - Modlink, Ethernet, Can
47
X8 - Modlink, Can
47
X9 - CAN, Analog Input
47
X20 - Motor Connector
48
X30 - Power Supply, X31/X32 Ballast Resistor
49
Connection Example for Three-Phase Supply With/Without Transformer
49
Connection Example for Single-Phase Supply up to Max. 230 VAC
50
Inputs and Outputs of the Logic Signals
51
8.2.10.1 X50 - Internal Inputs
51
8.2.10.2 X51 - Internal Outputs
51
X52 - 24 V Supply/Thermal Contact
52
Wiring of 24 V (Internal/External)
53
Error Indications FC0 to FC3 ( Red Flashing)
54
Status Indications FC0 to FC3 (Green and Red)
56
Indication of Malfunctions - RIO
56
Status of Controller - RON
56
Operation Indication - CNC
56
Indication "Remote Control" - REM
56
Status Indication/Error Messages of Bus Systems - STX/SRX/SRR
57
Test Pins - MP/GND
57
Coding Selector - ID
58
Layout Plan of the Output Stage 036050001
59
Layput Plan of the Output Stage 036050001.3
60
9 General Information Regarding the Wiring
61
General Information
61
Difficulties of Ground Loop
63
Motor Cable
64
Cables for the Rotor Position Detection
65
Cables for External Ballast Resistors
65
10 Option Modules
67
Option Module 061020043X
67
Two Serial Interfaces with RS232/RS485 Specification
69
X10 - Profibus
69
10.1.2.1 Bus Termination
70
10.1.2.2 Assignment of the Module Numbers
71
X13/X14 - Two Active Transducers
72
X13/X14 - Two Passive Transducers
74
X13/X14 - Two Analog Inputs (12 Bits)
76
Battery-Buffered RAM and Real-Time Clock
77
Option Module 061020044X
78
X17/X18 - Analog Output 1/2
79
X19 - Analog Input
80
X10 - Profibus
80
10.2.3.1 Bus Termination
81
10.2.3.2 Assignment of the Module Numbers
82
Option Module 061020045X
83
X11/X12 - Interbus
84
10.3.1.1 Meaning of the ID Code
85
X13/X14 - Two Active Transducers
86
X13/X14 - Two Passive Transducers
88
Two Serial Interfaces with RS232/RS485 Specification
90
X13/X14 - Two Analog Inputs (12 Bits)
91
Battery-Buffered RAM and Real-Time Clock
92
11 Electric Performance Dimensioning
93
Components
93
Output Stage
93
Power Supply
93
Motor
94
Power Consumption of a Drive
95
12 Appendix: Manufacturers
97
PHOENIX Connectors
97
Order Key for PHOENIX Connectors
97
Overvoltage Protection FLASHTRAB
98
Shield Terminal Blocks
99
SIBA Fuses
99
TOSHIBA - Fiber Optic Connectors
99
5
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the SIEB & MEYER CNC 61.00 and is the answer not in the manual?
Ask a question
SIEB & MEYER CNC 61.00 Specifications
General
Brand
SIEB & MEYER
Model
CNC 61.00
Category
Controller
Language
English
To Next PageTo Next Page
Need help?
General