Siemens SIMADYN D User Manual

Contents
xiv System- and communication configuring D7-SYS - SIMADYN D
Edition 12.2003
3.24.2 Channel marshalling blocks CCC4 and CDC4..................................................3-274
3.24.2.1 Group block CCC4.............................................................................................3-274
3.24.2.2 Distribution block CDC4.....................................................................................3-275
3.24.2.3 Compatible net data structure............................................................................3-276
3.24.3 Diagnostic outputs .............................................................................................3-276
3.24.3.1 Fault/error cause................................................................................................3-276
3.24.3.2 Channel assignment ..........................................................................................3-277
3.24.3.3 Channel statuses ...............................................................................................3-278
3.24.4 Introduction – "Pointer-based communication blocks" ......................................3-278
3.24.4.1 Principle mode of operation ...............................................................................3-279
3.24.4.2 Applications........................................................................................................3-279
3.24.4.3 Features of pointer-based communications ......................................................3-280
3.24.4.4 Associated function blocks ................................................................................3-281
3.24.4.5 Pointer interface.................................................................................................3-281
3.24.4.6 Configuring information and instructions ...........................................................3-282
3.24.4.7 Examples of CFC screenshots ..........................................................................3-282
3.25 Communications utility service ..........................................................................3-288
3.25.1 Function block SER ...........................................................................................3-289
3.25.2 System load, response times.............................................................................3-290
3.26 Communications utility time of day synchronization..........................................3-291
3.27 Communications with SIMATIC Operator Panels..............................................3-292
3.27.1 Configuring example..........................................................................................3-292
3.27.2 Configuring SIMADYN D....................................................................................3-293
3.27.2.1 Selecting the components in HWConfig ............................................................3-293
3.27.2.2 Configuring with CFC.........................................................................................3-294
3.27.2.2.1 Initializing the OP7.............................................................................................3-295
3.27.2.2.2 Reading function block connections (I/O)..........................................................3-295
3.27.2.2.3 Writing function block connections ....................................................................3-296
3.27.2.2.4 Configuring events.............................................................................................3-297
3.27.2.2.5 Configuring alarm messages.............................................................................3-298
3.27.2.2.6 Configuring the function keyboard.....................................................................3-299
3.27.2.2.7 Configuring the interface area ...........................................................................3-300
3.27.2.3 Importing the symbol table.................................................................................3-301
3.27.3 Configuring the OP7 with ProTool/Lite ..............................................................3-302
3.27.4 Application information.......................................................................................3-303
3.27.4.1 Computation times.............................................................................................3-303
3.28 Communications with WinCC (MPI) ..................................................................3-304
3.29 Communications with WinCC (SINEC H1)........................................................3-306
3.29.1 Prerequisites......................................................................................................3-306
3.29.2 Process variables...............................................................................................3-307
3.29.2.1 SIMADYN D software ........................................................................................3-307
3.29.2.2 Configuring WinCC ............................................................................................3-310
3.29.3 Binary events .....................................................................................................3-310
3.29.4 SIMADYN D messages......................................................................................3-310
3.29.4.1 SIMADYN D configuring software......................................................................3-310
3.29.4.2 WinCC configuring software ..............................................................................3-312
3.29.5 Generating the address book using the CFC editor..........................................3-312
3.29.6 NML configuring software for CSH11 ................................................................3-313

Siemens SIMADYN D Specifications

General

Brand	Siemens
Model	SIMADYN D
Category	Control Systems
Language	English