1-1. DSR-2000
Chapter 6 Setup Menu
116
Chapter 6 Setup Menu
Extended Menu
Item number Item name Settings
Menu items in the 300s, relating to editing operations (continued)
307 AUTO-DELETION
FOR
INCONSISTENT
DATA
Select what happens when an erroneous edit point is set.
MANU : A warning is given by flashing the DELETE button on the lower control panel.
The operator must manually delete the unnecessary edit point .
NEG&E: When inconsistent edit points are set, such as when an OUT point is before an
IN point, or an audio OUT point is before an audio IN point, or when too many edit
points are specified, the previously set edit point is deleted.
NEG: When inconsistent edit points are set, such as when an OUT point is before an IN
point, or an audio OUT point is before an audio IN point, the previously set edit point
is deleted. When too many edit points are specified, the DELETE button on the
control panel flashes to give a warning.
Note
Pressing the button corresponding to an edit point to be deleted and the DELETE button
simultaneously deletes the edit point. If an erroneous edit point is set (the DELETE
button is flashing), editing is not executed.
(Continued)
308 SELECTION OF
STD/NON-STD
FOR ANALOG
VIDEO IN
When no signal is input to the REF. VIDEO IN connector, select whether or not to
synchronize the playback circuits with the input analog video signal.
STD : Synchronize. Use this setting when a standard signal is always input (forced STD
mode).
N-STD: Do not synchronize. Use this setting when the input video signal is unstable
(forced NON-STD mode).
When using a VCR with no built-in time base corrector (e.g. a home-use VHS-system
VCR), select N-STD.
311
ANALOG AUDIO
EDIT PRESET
REPLACE FOR
CH1
312
ANALOG AUDIO
EDIT PRESET
REPLACE FOR
CH2
313
ANALOG AUDIO
EDIT PRESET
REPLACE FOR
CH3
314
ANALOG AUDIO
EDIT PRESET
REPLACE FOR
CH4
Items 311 to 314: When using an editor (PVE-500, BVE-600, etc.) or a remote controller
which cannot control digital audio edit preset, select how to activate edit preset of each
digital audio channel on this unit using the analog audio edit preset function of the editor
or remote controller.
Set edit preset of each digital audio channel (channels 1 to 4) of this unit on or off
according to the analog audio preset specified by the remote controller or editor.
NO DEFINITION
ANALOG CH1: Follow edit preset of analog channel 1.
ANALOG CH2: Follow edit preset of analog channel 2.
ANALOG CH1+CH2: Follow edit preset of analog channel 1 or 2.
The default settings for each item are as follows:
311: ANALOG CH1
312: ANALOG CH2
313: NO DEFINITION
314: NO DEFINITION
317 AUDIO EDIT
MODE
Specify the type of editing for audio signals.
CUT: Cut editing (discontinuity in audio signal may result at the editing point, causing
noise during playback.)
CROSS FADE : Cross-fade
FADE: Fade in and fade out
Chapter 6 Setup Menu
Chapter 6 Setup Menu
117
Item number Item name Settings
318
EDIT RETRY
When editing with two DSR-2000/2000P units, select the operation if the recorder was
not synchronized in time. (Make this setting on the recorder.)
OFF: Editing is not carried out, and the unit stops.
ON : The editing is automatically retried (up to twice).
327 AUDIO MODE
CHANGE
Select whether to allow audio data recorded on tape in two-channel mode (or four-
channel) to be re-recorded in four-channel (or two-channel mode).
OFF : Do not allow re-recording in a different audio mode.
ON: Allow re-recording in a different audio mode.
When this item is set to ON, the type of editing for audio signals is always a cut editing.
Menu items in the 300s, relating to editing operations (continued)
319
PREREAD
SELECT
Specify the preread editing operation.
A/V : Preread for both audio and video.
AUDIO: Preread for audio only.
VIDEO: Preread for video only.
The preread operation can be controlled with the PREREAD button on the control panel
or from the 9-pin remote control interface.
326
AUTOMATIC IN
ENTRY AFTER
AUTO EDIT
Select whether or not to automatically set the OUT point of the previous edit as the next
IN point at the end of an automatic edit.
OFF : No automatic setting.
R: Set recorder IN point automatically.
R & P: Set recorder IN point automatically, and also player IN point in two-VCR editing.
Item number Item name Settings
401 FUNCTION MODE
AFTER CUE-UP
Select the state that the unit goes into after a cuing-up operation.
STOP : Stops (the STOP mode).
STILL: Still playback (in search mode).
Note
When controlling this unit from the BVE-800 editor, set this item to STOP.
Menu items in the 400s, relating to preroll
403 AUTOMATIC
PREROLL
REFERENCE
ENTRY
Select whether or not the edit IN point is automatically set by pressing the PREROLL
button when the IN point is not set before starting preroll.
DIS : IN point is not set automatically.
ENA: I N point is set automatically.
335 OUT
REFERENCE
SELECT
When signals are input to both of the REF. VIDEO IN connector and the VIDEO IN
connector, determine which input signal to use as the reference signal.
REF VIDEO : Use the signal input to a REF. VIDEO IN connector as the reference video
signal.
The input video signal to be edited is required to be in synchronization with the
reference video signal.
VIDEO INPUT: Use the input video signal selected with the VIDEO INPUT button in the
INIPUT SELECT section.
To Next Page
Loading...
