Tegam 3550 - Page 133

Table A.3: Basic Accuracy Table [.05V to .10V]
Measure Frequency
Range Impedance
42Hz~99.9Hz 100Hz~1kHz 1.01kHz~10.0kHz 10.1kHz~30.0kHz 30.1kHz~100kHz 101kHz~1.00MHz 1.01MHz~5.00MHz
10.00mƻ~
100mƻ
199.99mƻ
0.1800ƻ~
1ƻ
1.9999ƻ
1.800ƻ~ (4+1.6ǃ)%+800 (3.2+0.16ǃ)%+40 (3.2+0.16ǃ)%+40 (3.2+0.16ǃ)%+40 (6+0.16ǃ)%+200 (6+0.16ǃ)%+200 (20+1.6ǃ)%+800
10ƻ
19.999ƻ
(4+0.8ǃ)%+80 (3.2+0.12ǃ)%+40 (3.2+0.12ǃ)%+40 (3.2+0.12ǃ)%+40 (6+0.12ǃ)%+200 (6+0.12ǃ)%+200 (20+1.2ǃ)%+800
18.00ƻ~ (0.6+0.08ǃ)%+40 (0.4+0.08ǃ)%+40 (0.6+0.08ǃ)%+40 (0.6+0.08ǃ)%+40 (1.6+0.2ǃ)%+160 (2.4+0.2ǃ)%+200 (12+0.2ǃ)%+200
100ƻ
199.99ƻ
(0.6+0.04ǃ)%+40 (0.4+0.04ǃ)%+40 (0.4+0.04ǃ)%+40 (0.4+0.04ǃ)%+40 (1.6+0.12ǃ)%+160 (2.4+0.12ǃ)%+160 (12+0.12ǃ)%+600
0.1800kƻ~ (0.6+0.04Į)%+40 (0.4+0.04Į)%+40 (0.6+0.2Į)%+40 (0.6+0.2Į)%+40 (1.6+0.2Į)%+160 (2.4+0.2Į)%+200 (12+0.2ǃ)%+1400
1kƻ
1.9999kƻ
(0.4+0.02Į)%+40 (0.4+0.02Į)%+40 (0.4+0.12Į)%+40 (0.4+0.12Į)%+40 (1.6+0.12Į)%+160 (2.4+0.12Į)%+160 (12+0.2ǃ)%+1400
1.800kƻ~ (0.6+0.04Į)%+40 (0.4+0.04Į)%+40 (0.6+0.2Į)%+40 (0.6+0.2Į)%+40 (4+0.2Į)%+400 (12+0.2Į)%+1600
10kƻ
19.999kƻ
(0.4+0.02Į)%+40 (0.4+0.02Į)%+40 (0.4+0.12Į)%+40 (0.4+0.12Į)%+40 (1.6+0.12Į)%+160 (4+0.12Į)%+280 (12+0.2Į)%+1200
18.00kƻ~ (0.6+0.04Į)%+40 (0.4+0.04Į)%+40 (0.6+0.2Į)%+40 (3.2+0.2Į)%+200 (4+0.2Į)%+200 (12+0.2Į)%+1200
100kƻ
199.99kƻ
(0.4+0.02Į)%+40 (0.4+0.02Į)%+40 (0.4+0.12Į)%+40 (3.2+0.2Į)%+720 (8+0.2Į)%+720 (12+0.2Į)%+720
0.1800Mƻ~
1Mƻ
1.9999Mƻ
1.800Mƻ~
10Mƻ
19.999Mƻ
18.00Mƻ~
100Mƻ
199.99Mƻ
Upper Specification: Accuracy of |Z| ± (Nominal% + Counts) Lower Specification: Accuracy of LJ ± (Nominal% + Counts)
Accuracy Limit from
Measurement Limit Chart
X
Maximum Voltage
Limit for Chart
The Set Measurement Voltage
The count coefficient should be calculated as follows:
Zx = the number of counts for |Z|
E
Zx
10,000
D
Zx
10,000
A.7