Tegam 3550 - Page 134

Table A.4: Basic Accuracy Table [.11V to .20V]
Measure Frequency
Range Impedance
42Hz~99.9Hz 100Hz~1kHz 1.01kHz~10.0kHz 10.1kHz~30.0kHz 30.1kHz~100kHz 101kHz~1.00MHz 1.01MHz~5.00MHz
10.00mƻ~
100mƻ
199.99mƻ
0.1800ƻ~ (4+0.8ǃ)%+400 (2+0.8ǃ)%+400 (3+0.8ǃ)%+400 (3+0.8ǃ)%+400 (4+0.8ǃ)%+400 (6+0.8ǃ)%+400
1ƻ
1.9999ƻ
(4+0.6ǃ)%+80 (2+0.4ǃ)%+80 (3+0.4ǃ)%+80 (3+0.4ǃ)%+120 (4+0.4ǃ)%+300 (6+0.4ǃ)%+500
1.800ƻ~ (2+0.8ǃ)%+400 (1.6+0.08ǃ)%+20 (1.6+0.08ǃ)%+20 (1.6+0.08ǃ)%+20 (3+0.08ǃ)%+100 (3+0.08ǃ)%+100 (10+0.8ǃ)%+400
10ƻ
19.999ƻ
(2+0.4ǃ)%+40 (1.6+0.06ǃ)%+20 (1.6+0.06ǃ)%+20 (1.6+0.06ǃ)%+20 (3+0.06ǃ)%+100 (3+0.06ǃ)%+100 (10+0.6ǃ)%+400
18.00ƻ~ (0.3+0.04ǃ)%+20 (0.2+0.04ǃ)%+20 (0.3+0.04ǃ)%+20 (0.3+0.04ǃ)%+20 (0.8+0.1ǃ)%+80 (1.2+0.1ǃ)%+100 (6+0.1ǃ)%+100
100ƻ
199.99ƻ
(0.3+0.02ǃ)%+20 (0.2+0.02ǃ)%+20 (0.2+0.02ǃ)%+20 (0.2+0.02ǃ)%+20 (0.8+0.06ǃ)%+80 (1.2+0.06ǃ)%+80 (6+0.06ǃ)%+300
0.1800kƻ~ (0.3+0.02Į)%+20 (0.2+0.02Į)%+20 (0.3+0.1Į)%+20 (0.3+0.1Į)%+20 (0.8+0.1Į)%+80 (1.2+0.1ǃ)%+100 (6+0.1ǃ)%+700
1kƻ
1.9999kƻ
(0.2+0.01Į)%+20 (0.2+0.01Į)%+20 (0.2+0.06Į)%+20 (0.2+0.06Į)%+20 (0.8+0.06Į)%+80 (1.2+0.06ǃ)%+80 (6+0.1ǃ)%+700
1.800kƻ~ (0.3+0.02Į)%+20 (0.2+0.02Į)%+20 (0.3+0.1Į)%+20 (0.3+0.1Į)%+20 (0.8+0.1Į)%+80 (2+0.1Į)%+200 (6+0.1Į)%+800
10kƻ
19.999kƻ
(0.2+0.01Į)%+20 (0.2+0.01Į)%+20 (0.2+0.06Į)%+20 (0.2+0.06Į)%+20 (0.8+0.06Į)%+80 (2+0.06Į)%+140 (6+0.1Į)%+600
18.00kƻ~ (0.3+0.02Į)%+20 (0.2+0.02Į)%+20 (0.3+0.1Į)%+20 (1.6+0.1Į)%+100 (2+0.1Į)%+100 (6+0.1Į)%+600
100kƻ
199.99kƻ
(0.2+0.01Į)%+20 (0.2+0.01Į)%+20 (0.2+0.06Į)%+20 (1.6+0.1Į)%+360 (4+0.1Į)%+360 (6+0.1Į)%+360
0.1800Mƻ~ (3+0.2Į)%+40 (3+0.2Į)%+40 (3+0.2Į)%+40 (4+0.2Į)%+140 (4+0.2Į)%+140
1Mƻ
1.9999Mƻ
(3+0.2Į)%+40 (3+0.2Į)%+40 (3+0.2Į)%+40 (4+0.2Į)%+400 (4+0.2Į)%+500
1.800Mƻ~ (4+0.3Į)%+40 (4+0.3Į)%+40 (4+0.3Į)%+40
10Mƻ
19.999Mƻ
(4+0.2Į)%+80 (4+0.2Į)%+80 (4+0.2Į)%+80
18.00Mƻ~ (10+0.3Į)%+1000 (10+0.3Į)%+1000 (10+0.3Į)%+1000
100Mƻ
199.99Mƻ
(10+0.2Į)%+800 (10+0.2Į)%+800 (10+0.2Į)%+800
Upper Specification: Accuracy of |Z| ± (Nominal% + Counts)
Accuracy Limit from
Measurement Limit Chart
X
Maximum Voltage
Limit for Chart
The Set Measurement Voltage
Lower Specification: Accuracy of LJ ± (Nominal% + Counts) The count coefficient should be calculated as follows:
Zx = the number of counts for |Z|
E
Zx
10,000
D
Zx
10,000
A.8