Tektronix TG8000

Index
OUTPut1:ZONE:
FREQuency?, 120
OUTPut1:ZONE:K, 120
OUTPut1:ZONE:K?, 120
OUTPut1:ZONE:KT, 121
OUTPut1:ZONE:KT?, 121
OUTPut1:ZO
NE:KTSQ, 121
OUTPut1:ZONE:KTSQ?, 121
OUTPut1:ZONE:KX, 120
OUTPut1:ZONE:KX?, 120
OUTPut1:ZONE:KXSQ, 120
OUTPut1:ZONE:KXSQ?, 120
OUTPut1:
ZONE:KXT, 120
OUTPut1:ZONE:KXY, 120
OUTPut1:ZONE:KXY?, 120
OUTPut1:ZONE:KY, 120
OUTPut1:ZONE:KY?, 120
OUTPut1:ZONE:KYSQ, 120
OUTPu
t1:ZONE:KYSQ?, 121
OUTPut1:ZONE:KYT, 121
OUTPut1:ZONE:KYT?, 121
OUTPut1:ZONE:SAVE, 121
OUTPut1:ZONE:TRESet:
STATe, 121
OUT
Put1:ZONE:TRESet:
STATe?, 121
OUTPut1:ZONE:VIDEO:PB:
STATe, 121
OUTPut1:ZONE:VIDEO:PB:
STATe?, 122
O
UTPut1:ZONE:VIDEO:PR:
STATe, 122
OUTPut1:ZONE:VIDEO:PR:
STATe?, 122
OUTPut1:ZONE:VIDEO:Y:
STATe, 121
OUTPut1:ZONE:VIDEO:Y:
STATe?, 121
OUTPut1:ZONE:WAVE, 121
OUTPut1:ZONE:WAVE?, 121
OUTPut2:SIGNal, 74, 143
OUTPut2:SIGNal?, 74, 144
OUTPut2:STANdard, 35, 74, 143
OUTPut2:STANdard?, 35
OUTPut3:STANdard?, 35, 36
OUTPut4:LTC[1]:STATE, 94
OUTPut4:LTC[1
/2/3/4]:
LEVel, 94
OUTPut4:LTC[1/2/3/4]:
LEVel?, 94
OUTPut4:LTC[1/2/3/4]:
MDELay, 94
OUTPut4:LT
C[1/2/3/4]:
OFFSet, 94
OUTPut4:LTC[1/2/3/4]:
OFFSet?, 94
OUTPut4:LTC[1/2/3/4]:
SOURce, 93
OUTPut4:
LTC[1/2/3/4]:
SOURce?, 94
OUTPut4:LTC[1/2/3/4]:
TYPE, 94
OUTPut4:TIMECode:ATC:
STATe, 144
OUTPu
t4:TIMECode:ATC:
STATe?, 144
OUTPut4:TIMECode:DROPf:
STATe, 62
OUTPut4:TIMECode:DROPf:
STATe?, 62
OUT
Put4:TIMECode:LINe, 62,
144
OUTPut4:TIMECode:LINe?, 62
OUTPut4:TIMECode:
OFFSet, 62, 144
OUTPut4:TIMECode:
S
OURce, 62, 144
OUTPut4:TIMECode:
SOURce?, 62, 144
OUTPut4:TIMECode:
STATus?, 62
OUTPut4:TIMECode:VITc[1/2]:
STATe, 62
P
Preface, v
PROGram[:SELected]:
NAME, 21
PROGram[:SELected]:
NAME?, 21
PROGram[:SELected]:STATe, 21
PROGram[:SELected]:
STATe?, 21
PROGram[:SELe
cted]:WAIT, 21
PROGram:EXPLicit:STATe, 21
PROGram:EXPLicit:STATe?, 21
PROGram:EXPLicit:WAIT, 21
PROGram:EXPLicit:WAIT?, 22
Programming, 5
PTRansitio
n, 24
PTRansition?, 24
Q
Queries, 8
Quotes, 10
R
Related Manuals, v
*RST, 15
Rules
command forming, 5
for using SCPI commands, 10
S
SCPI
abbreviating, 9
chaining commands, 9
com
mands, 7
general rules, 10
parameter types, 8
programming, 5
subsystem hierarchy tree, 7
SCPI commands and queries
s
yntax, 7
creating commands, 7
creating queries, 8
SDI7 OUTPUT commands, 147
SDI7 Remote commands, 147
SDI7 SENSE commands, 171
SENSe<1|2>:CORRection:
MDELay:HORizontal, 171
SENSe<1|2>:CORRection:
MDELay:HORizontal?, 172
SENSe<1|2>:CORRection:
MDELay:RELative, 172
SENSe<1|2>:CORRection:
MDELay:VERTical, 172
SENSe<1|2>:CORRection:
MDELay:VERTical?, 172
Draft
186 TG8000 Multiformat Test Signal Generator Programmer Manual