What to do if my Telstar LyoQuest pump does not reach the vacuum pressure limit?
If your Telstar Laboratory Equipment vacuum pump isn't reaching the vacuum pressure limit, it might be due to a lack of oil. Check the oil level and add more until it reaches the appropriate quantity. Alternatively, the oil could be contaminated. In this case, empty the old oil and refill the pump with new oil.
Why my Telstar Laboratory Equipment vacuum pump does not start?
If the Telstar Laboratory Equipment vacuum pump does not start, several issues could be the cause. First, check the connection of the on/off switch located on the motor of the pump. Also, examine the electrical connection terminals of the pump and the corresponding circuit-breaker. The environmental temperature might be too high (over 35ºC), which could cause the circuit to break. Finally, the pump's starter protector may be blocked because the condenser isn't at the correct temperature. The minimum temperature to switch on the pump is: LQ-55
How to prevent abnormal heating of Telstar LyoQuest pump?
If the Telstar Laboratory Equipment pump is heating abnormally, it may be due to poor ventilation or a high environmental temperature (above 35ºC). Try placing the pump in an area with better ventilation to resolve this issue.
What to do if I see mist leak from the emission channel of Telstar LyoQuest?
If you notice mist leaking from the emission channel of your Telstar Laboratory Equipment, it could be because the Gas-Ballast is opened too much; try closing it. Another possible reason is a leak somewhere in the system; try to locate the leak.
What to do if Telstar Freezer pump doesn’t reach the vacuum pressure limit?
If the pump in your Telstar Freezer isn’t reaching the vacuum pressure limit, it could be due to: * Lack of oil: Check the oil level and add oil up to the suitable quantity. * Contaminated oil: Empty the old oil from the pump and refill it with new oil.
Why is my Telstar Freezer pump heating up abnormally?
Abnormal heating of the Telstar Freezer pump can be caused by a lack of ventilation or an environmental temperature that is too high (above 35ºC). Place the pump in an area with better ventilation.
What to do if Telstar Freezer refrigerating unit doesn’t start up?
If the refrigerating unit of your Telstar Freezer isn’t starting, check the electrical connection terminals of the compressors. Also, check the circuit breaker corresponding to each compressor.
Why I cannot obtain vacuum in Telstar Freezer?
If the motor turns but doesn’t create vacuum, contact Azbil Telstar Technologies Customer Service.
What to do if Telstar Freezer has mist leak from the emission channel?
If you notice a mist leak from the emission channel of your Telstar Freezer, it could be due to the Gas-Ballast being opened too much. Try closing the Gas-Ballast. It may also be due to a leak, so try to locate it.
What to do if Telstar Freezer condenser doesn’t reach the minimum temperature?
If the condenser in your Telstar Freezer isn’t reaching the minimum temperature, it may be due to refrigerant leak, in this case contact Azbil Telstar Technologies Customer Service. Alternatively, the refrigerating fans of the refrigerating unit may not be working; check the circuit breaker corresponding to each fan.
Explains the purpose of the manual for LyoQuest/LyoQuest Arctic freeze dryers.
Details the uses of the freeze-dryer for various products in flasks, vials, or bulk.
Presents specifications for Vacuum Pump, Ice Condenser, Refrigerating Unit, and Equipment.
Guides on handling, inspecting, and unpacking the freeze-dryer upon delivery.
Details requirements for placing the unit, including surface and working conditions.
Provides instructions for connecting the freeze-dryer to the power supply safely.
Explains vacuum pump oil level, gas-ballast, exhaust filter, and connections.
Advises on ensuring proper cooling by maintaining ventilation around the unit.
Describes the compact desktop design, metallic box, access doors, control panel, and refrigerating system.
Recommends opening the water drain valve to ensure the condenser is empty before each operation.
Advises on lightly greasing airtight seals with silicone grease and keeping contact surfaces clean.
Provides instructions for extended shutdown, including changing oil, cleaning, and lubricating gaskets.
Explains how the product is frozen in the condenser or plate stack and factors affecting freezing speed.
Introduces the process of lyophilization and its modes.
Introduces the two modes: AUTOMATIC and SEMIAUTOMATIC, and recipe usage.
Details the Freezing, Cool+Vacuum, and Heat plates processes and their parameters.
Lists different chamber models with their diameters, distances between plates, and materials.
Describes horizontal and circular manifolds with different inlet configurations.
Explains the function of the drip tray to collect condensation from flasks.
Details the software for monitoring vacuum and temperatures, including computer requirements.
Instructions on how to start the equipment and access the main screen.
Explains how to access the freeze-drying window and its components.
Describes how to access the probes window to view sensor values.
Explains how to access and view the loaded recipe in the PLC.
Details how to select and load a recipe for editing from the available options.
Guides on selecting processes in semiautomatic mode.
Introduces auxiliary cycles like Defrosting and Alarms.
Explains how to access the Defrosting window and start/stop the process.
Describes how to access the Alarms window to view active, muted, and corrected alarms.
Provides a list of alarm messages and their corresponding descriptions.
Explains how to access the Synoptic window to view equipment component status and values.
Describes how to access the Settings window to adjust various parameters.
Details how to select the user interface language from a list of options.
Explains how to set the system's date and time.
Guides on configuring local network settings, including IP address and subnet mask.
Accesses a restricted window for technical service, requiring a password for factory parameters.
Explains how to create and edit recipes, including steps, processes, and parameters.
Details how to select and load a recipe for editing from the available options.
Introduces user management, including login, password changes, and log out.
Defines user levels: Administrators and Operators, outlining their access privileges.
Describes how to log in using a username and password.
Explains the procedure for changing a user's password through a pop-up window.
Details how to manage users, including adding, editing, and removing them.
Explains automatic and manual methods for logging out of the system.
Offers guidelines for cleaning and disinfecting the freeze-dryer unit and its components.
Details routine and radical cleaning methods, recommended tools, and cleaning products.
Explains the necessity of disinfection after cleaning and lists recommended disinfectants.
Covers maintenance for the vacuum pump, including oil level, condition, leaks, and cleaning.
Discusses maintenance for the refrigerating system, including refrigerant types and cleaning grids.
Presents a table detailing maintenance operations, their periodicity, and suggested values.
Addresses common problems with the vacuum pump, such as not starting or not obtaining vacuum.
Covers troubleshooting for the refrigerating unit, including start-up issues and compressor stoppages.
Addresses issues related to reaching working vacuum and gauge errors.
Lists spare part codes for vacuum units, refrigerating systems, and general components.
Provides two sample recipes for mushrooms and skimmed milk lyophilization.
Provides tables to record maintenance operations performed on the vacuum pump and compressors.
A form for the customer to declare decontamination status for safe handling.
Presents the Piping and Instrumentation Diagram for the LyoQuest -55 refrigerating system.
Presents the Piping and Instrumentation Diagram for the LyoQuest -85 refrigerating system.
Presents the Piping and Instrumentation Diagram for the LyoQuest Arctic -85 refrigerating system.
Presents the Piping and Instrumentation Diagram for the vacuum system.
EU Declaration of Conformity for the LyoQuest / LyoQuest Arctic equipment.
Illustrates the configuration of various optional accessories for the LyoQuest chambers.
General| Brand | Telstar |
|---|---|
| Model | LyoQuest |
| Category | Laboratory Equipment |
| Language | English |
To Next Page
