Toa A-9120DHM2 - UTILITY Setting Flow Chart

73
10.4. UTILITY Setting Flow Chart
0 1 - S C E N E 1
Normal use state
UTILITY
S T E R E O L I N K S T E R E O L I N K O U T 1 2? S T E R E O L I N K O U T 1 = 2
(p.76-C2)
(p.76-C1)
: Selects OUT.
P
The screen display examples may differ from actual displays.
The on-screen indications shown in blue are variable parameters
by key operation.
The symbols in the figure represent the following key operation.
: Screen shift key (up and down)
: Screen shift key (right) or ENTER key
: Screen shift key (left) or ESC key
: PARAMETER knob
or
- : Input channel ON/OFF key
: Output channel ON/OFF key
I-ON/OFF
O-ON/OFF
P
18
or
P
or
P
To/from lowermost screen
N O M N O M A T T E N U A T E 0
: 1 to 20
P
Cancel
STEREO LINK
(p.76-C3)
or
P
C - I N S E T T I N G C - I N 0 1 - > N O N E
Control input terminal's function
setting (p. 76)
Control output terminal's function
setting (p. 77)
: 01 to 12
P
(p.76-C4) (p.77-C5)
or
(p.77-C8)
or
P
C - O U T S E T T I N G C - O UT 0 1 - > N O N E
: 01 to 12
P
P
P
C - I N I N F O R M A T I O N C - I N F U N C T I O N C - I N I N F 0 1 = N O N E
: 01 to 12
P
(p.77-C6)
(p.77-C7)
C - I N S T A T U S C I N =
- - - - - - - - - - - -
(All open)
C I N = 1 2 3 4 5 6 7 8 9 A B C
(All open)
(p.77-C9) (p.78-C10)
or
or
P
P
P
C - O U T I N F O R M A T I O N C - O U T F U N C T I O N C - O U T I N F 0 1 = N O N E
: 01 to 12
P
(p.78-C11)
(p.78-C12)
C - O U T S T A T U S C O U T =
- - - - - - - - - - - -
(All close)
C O U T = 1 2 3 4 5 6 7 8 9 A B C
(All close)
(p.78-C13)
or
P
or
P
P
R E M O T E R E M O T E S E T T I N G
(p.79-C16)
Z M I N F O R M A T I O N
(p.78-C14)
(p.78-C14)
R E M O T E 1 - > V O L U M E R E M O T E 1 - > V O L U M E
(p.79-C15)
R E M O T E 1 - > O U T P U T 1
: OFF, VOLUME, ZM-9001,
ZM-9002
P
: 1, 2
P
: 01 to 16
P
: SW1 to 8, VOLUME
P
: Selects IN or OUT.
P
(p.79-C17)
(p.79-C18)
Z M I N F I D 0 1 = 9 0 1 1 I D 0 1 S W 1 = L D B A N K 0 1 I D 0 1 V O L U M E = O U T 1
(When VOLUME is selected)
To the next page
M O N I T O R A N C M O N S E L E C T = O F F
A N C M O N S E L E C T = O N M O N S E L E C T - > C - I N 0 1
P
(p.79-C19)
Above display is skipped if no
ANC module is installed.
: Selects CIN.
P
(p.80-C20)
S E L E C T S Y N C - > A N 1
: AN1 to 4
P
(p.80-C22)
A N 1 S Y N C - > C O U T 0 1
: 01 to 12
P
(p.80-C23)
(p.80-C21)
M O N S E L S Y N C = O F F
M O N S E L S Y N C = O N
P