Watlow ez-zone pm - Page 130

Watlow EZ-ZONE
®
PM Integrated Controller • 127 • Chapter 11 Appendix
Minimum Off Time 56
Minimum On Time 56
Minutes 89
Modbus Register Mapping 56
Modbus TCP 30
Modbus TCP Enable 86
Modbus Word Order 82
Monitor Menu 43
N
navigating
Factory Page 92
pages and menus 33
Proling Page 88
Setup Page 39, 55
No-arc Relay 104
Non-volatile Save 56
O
on-off control 106
Open Loop Detect Deviation 69
Open Loop Detect Enable 68
Open Loop Detect Time 69
Open Loop Set Point 46
Operations Page 39
ordering information
integrated controller models 123
output activity lights 32
output conguration 105
Output Function 71
Output Menu 70
Output Point 1 55
Output Point 2 55
Output Point 3 55
Output Point 4 55
Output Point 5 55
Output Point 6 55
Output Point 7 55
Output Point 8 55
Output Point 9 55
Output Point 10 55
output power scaling 105
outputs 4
Output State 42
Output Type 71
P
P3T armor sealing system 2
Parameter 1 to 20 93
Parity 82
Part Number 96
Password 96
Peltier Delay 55, 68
percent units indicator light 32
Power Off Level A 56
Power On Level A 56
Power Out Time 56, 81
Pressure Units 55
process alarms 111
Process Error Enable 58
Process Error Low 58
Process Value 40, 55, 62
Process Value Active 44
Process Value Menu 41
Probus Address Lock 83
Probus DP 30, 38
Probus Node Address 83
prole activity light 32
Prole Status Menu 51
Prole Type 80
Proling Page 88
proling parameters 88
programming the Home Page 100
proportional control
plus integral (PI) control 107
plus integral plus derivative (PID)
control 107
Protocol 81
Public Key 96
Q
R
Ramp Action 69
Ramp Rate 69, 108
Ramp Scale 69, 108
Range High 58, 72, 103
Range Low 58, 72, 103
Ratio Control 110
Read 49, 112
Read Lockout Security 113
Real Time Clock 56
receiving a remote set point 104
Remote Enable 44, 104
restoring user settings 100
retransmit 104
Retransmit Source 71
Rolling Password 95
RTD Leads 57
S
saving user settings 100
Scale High 57, 72, 103
Scale Low 57, 72, 103
Seconds 90
secure settings 99, 113
Security Setting 94, 96
sensor backup 103
Sensor Backup Enable 103
sensor selection 103
Sensor Type 57, 101, 103
Serial Number 96
Set Lockout Security 113
set point high limit 103
Set Point High Limit Open Loop 70
set point low limit 103
Set Point Low Limit Open Loop 70
Setup Page 55
Sides
Alarm 74
Limit 66
Silencing 74, 112
single set point ramping 108
Software Build 96
Software Revision 96
Source 73
Source Function A 56
Source Function E 56
Source Instance A 56
Source Instance E 56
Special Output Function 56
Special Output Function Menu 50
Step Time Remaining 53
System Security 99, 113
T
Target Set Point 89
temperature units indicator lights 32
Thermistor 57
Time Base 64, 71
Time Derivative 46, 101, 107
Time Integral 46, 101, 107
TRU-TUNE+™ Band 67, 101
TRU-TUNE+™ Enable 67, 101
TRU-TUNE+™ Gain 67, 101
tuning the PID parameters 100
Type 73, 111
U
Up Key 32
upper display 32
User Failure Action 68
User Password 95
User Restore Set 81, 100
User Save Set 81, 100
User Tune Aggressiveness 100
using the software 112
V
Valve Travel Time 56
variable time base 108
W
Wait Event (1 and 2) 90, 91
Wait For Process Instance 90
Wait For Time 89
weight 122
wiring
digital input or output 5 22, 23
digital input or output 6 23
EIA-232/485 Modbus RTU commu-
nications 29
high power 22
input 1 process 24
input 1 RTD 23
input 1 thermocouple 23
input 2 current transformer 24
input 2 thermocouple 24
low power 22
Modbus RTU or standard bus EIA-
485 communications 29