Watlow ez-zone pm - Page 127

Watlow EZ-ZONE
®
PMI Controller • 123 • Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range Default
Modbus
Relative Ad-
dress
CIP -
Class
Instance
Attribute
hex (dec)
Pro-
fibus
Index
Param-
eter
ID
Data
Type
and
Access
**
rp
rP
Control Loop (1 to
2)
Ramp Action
Select when the
controller's set
point will ramp to
the defined end set
point.
off Off (62)
str Startup (88)
stpt Set Point
Change (85)
both Both (13)
Off Instance 1
Map 1 Map 2
2186 2666
Instance 2
Map 1 Map 2
2266 2746
0x6B
(107)
1 to 2
0xE (14)
56 7014 uint
RWES
r.sC
r.SC
Control Loop (1 to
2)
Ramp Scale
Select the scale of
the ramp rate.
hoUr Hours (39)
ЛЏin Minutes (57)
Minutes Instance 1
Map 1 Map 2
2188 2668
Instance 2
Map 1 Map 2
2268 2748
0x6B
(107)
1 to 2
0xF (15)
57 7015 uint
RWES
r.rt
r.rt
Control Loop (1 to
2)
Ramp Rate
Set the rate for the
set point ramp. Set
the time units for
the rate with the
Ramp Scale param-
eter.
0.0 to 9,999.000°F or
units
0.0 to 5,555.000°C
1.0°F or
units
1.0°C
Instance 1
Map 1 Map 2
2192 2672
Instance 2
Map 1 Map 2
2272 2752
0x6B
(107)
1 to 2
0x11
(17)
58 7017 float
RWES
L.sp
L.SP
Control Loop (1 to
2)
Minimum Set Point
Set the minimum
value of the closed
loop set point
range.
-1,999.000 to
9,999.000°F or units
-1,128.000 to
5,537.000°C
-1,999°F
or units
-1,128°C
Instance 1
Map 1 Map 2
2164 2644
Instance 2
Map 1 Map 2
2244 2724
0x6B
(107)
1 to 2
3
52 7003 float
RWES
h.sp
h.SP
Control Loop (1 to
2)
Maximum Set Point
Set the maximum
value of the closed
loop set point
range.
-1,999.000 to
9,999.000°F or units
-1,128.000 to
5,537.000°C
9,999°F
or units
5,537°C
Instance 1
Map 1 Map 2
2166 2646
Instance 2
Map 1 Map 2
2246 2726
0x6B
(107)
1 to 2
4
53 7004 float
RWES
C.sp
C.SP
Control Loop (1 to
2)
Set Point *
Set the set point
that the controller
will automatically
control to.
-1,999.000 to
9,999.000°F or units
-1,128.000 to
5,537.000°C
75.0°F
or units
24.0°C
Instance 1
Map 1 Map 2
2160 2640
Instance 2
Map 1 Map 2
2240 2720
0x6B
(107)
1 to 2
1
49 7001 float
RWES
* These parameters/prompts are available in these menus with firmware revisions 11.0 and above.
** R: Read, W: Write, E: EEPROM, S: User Set