Parameter List
3
3.5 b: Application
YASKAWA TOEPYAIGA5001A GA500 DRIVE MAINTENANCE & TROUBLESHOOTING 101
No.
(Hex.)
Name Description
Default
(Range)
b3-33
(0B3F)
Expert
Speed Search during Uv
Selection
Sets the function that starts Speed Search at start-up if the drive detects a Uv [Undervoltage] when it
receives a Run command.
0 : Disabled
1 : Enabled
1
(0, 1)
b3-39
(1B8F)
Expert
Regen Judgment Lv of Spd
Search
Sets the level to determine the regenerative state during speed search. Usually it is not necessary to
change this setting.
15%
(0 - 50%)
b3-54
(3123)
Search Time Sets the length of time that the drive will run Speed Search. 400 ms
(10 - 2000 ms)
b3-55
(3124)
Expert
Current Increment Time Sets the length of time that the drive will increase the current from zero current to the setting value of
b3-06 [Speed Estimation Current Level 1].
10 ms
(10 - 2000 ms)
b3-56
(3126)
InverseRotationSearch
WaitTime
Sets the wait time until the drive starts inverse rotation search after it completes forward search when
you do inverse rotation search during Current Detection Speed Search.
Determined by o2-04
(0.1 - 5.0 s)
b3-61
(1B96)
Expert
Initial Pole Detection
Response Gain
Sets the responsiveness for initial motor magnetic pole calculation when A1-02 = 6 [Control Method
Selection = AOLV/PM]. Set b3-61 > 0.0 for an ordinary IPM motor.
It is automatically set if High Frequency Injection Tuning is used.
Note:
• Set n8-35 = 1 [Initial Pole Calculation Method = High Frequency Injection] to enable this
parameter.
• Set n8-41 [HFI P Gain] to adjust the responsiveness for initial motor magnetic pole calculation
when A1-02 = 5 [OLV/PM].
5.0
(-20.0 - +20.0)
◆ b4: Timer Function
No.
(Hex.)
Name Description
Default
(Range)
b4-01
(01A3)
Timer Function ON-Delay
Time
Sets the ON-delay time for the timer input. 0.0 s
(0.0 - 3000.0 s)
b4-02
(01A4)
Timer Function OFF-Delay
Time
Sets the OFF-delay time for the timer input. 0.0 s
(0.0 - 3000.0 s)
b4-03
(0B30)
Expert
Terminal M1-M2 ON-Delay
Time
Sets the delay time to activate the contact after the function set in H2-01 activates. 0 ms
(0 - 65000 ms)
b4-04
(0B31)
Expert
Terminal M1-M2 OFF-Delay
Time
Sets the delay time to deactivate the contact after the function set in H2-01 deactivates. 0 ms
(0 - 65000 ms)
b4-05
(0B32)
Expert
Terminal M3-M4 ON-Delay
Time
Sets the delay time to activate the contact after the function set in H2-02 activates. 0 ms
(0 - 65000 ms)
b4-06
(0B33)
Expert
Terminal M3-M4 OFF-Delay
Time
Sets the delay time to deactivate the contact after the function set in H2-02 deactivates. 0 ms
(0 - 65000 ms)
b4-07
(0B34)
Expert
Terminal P2 ON-Delay Time Sets the delay time until the contact is turned ON after the function set with H2-03 turns ON. 0 ms
(0 - 65000 ms)
b4-08
(0B35)
Expert
Terminal P2 OFF-Delay
Time
Sets the delay time to deactivate the contact after the function set in H2-03 deactivates. 0 ms
(0 - 65000 ms)
To Next Page
Loading...
