3.13 o: Keypad-Related Settings
162 YASKAWA TOEPYAIGA5001A GA500 DRIVE MAINTENANCE & TROUBLESHOOTING
No.
(Hex.)
Name Description
Default
(Range)
o1-32
(11B5)
RUN
Custom Monitor 9 You can select a maximum of 12 monitors as user monitors and set them to parameters o1-24 to o1-
35. This parameter sets the user monitor to show on the ninth line.
0
(0, 101 - 999)
o1-33
(11B6)
RUN
Custom Monitor 10 You can select a maximum of 12 monitors as user monitors and set them to parameters o1-24 to o1-
35. This parameter sets the user monitor to show on the 10th line.
0
(0, 101 - 999)
o1-34
(11B7)
RUN
Custom Monitor 11 You can select a maximum of 12 monitors as user monitors and set them to parameters o1-24 to o1-
35. This parameter sets the user monitor to show on the 11th line.
0
(0, 101 - 999)
o1-35
(11B8)
RUN
Custom Monitor 12 You can select a maximum of 12 monitors as user monitors and set them to parameters o1-24 to o1-
35. This parameter sets the user monitor to show on the 12th line.
0
(0, 101 - 999)
o1-36
(11B9)
RUN
LCD Backlight Brightness Sets the intensity of the LCD keypad backlight. 5
(1 - 5)
o1-37
(11BA)
RUN
LCD Backlight ON/OFF
Selection
Sets the automatic shut off function for the LCD backlight.
0 : OFF
1 : ON
1
(0, 1)
o1-38
(11BB)
RUN
LCD Backlight Off-Delay Sets the time until the LCD backlight automatically turns off. 60 s
(10 - 300 s)
o1-39
(11BC)
RUN
Show Initial Setup Screen Sets the function to show the LCD keypad initial setup screen each time you energize the drive. This
parameter is only available with an LCD keypad.
0 : No
1 : Yes
1
(0, 1)
o1-40
(11BD)
RUN
Home Screen Display
Selection
Sets the monitor display mode for the Home screen. This parameter is only available with an LCD
keypad.
0 : Custom Monitor
1 : Bar Graph
2 : Analog Gauge
3 : Trend Plot
0
(0 - 3)
o1-41
(11C1)
RUN
1st Monitor Area Selection Sets the horizontal axis value used to display the monitor set in o1-24 [Custom Monitor 1] as a bar
graph. This parameter is only available with an LCD keypad.
0 : +/- Area ( - o1-42 ～ o1-42 )
1 : + Area ( 0 ~ o1-42 )
0
(0 - 1)
o1-42
(11C2)
RUN
1st Monitor Area Setting Sets the horizontal axis value used to display the monitor set in o1-24 [Custom Monitor 1] as a bar
graph. This parameter is only available with an LCD keypad.
100.0%
(0.0 - 100.0%)
o1-43
(11C3)
RUN
2nd Monitor Area Selection Selects the horizontal range used to display the monitor set in o1-25 [Custom Monitor 2] as a bar
graph. This parameter is only available with an LCD keypad.
0 : +/- Area ( - o1-44 ～ o1-44 )
1 : + Area ( 0 ~ o1-44 )
0
(0 - 1)
o1-44
(11C4)
RUN
2nd Monitor Area Setting Sets the horizontal axis value used to display the monitor set in o1-25 [Custom Monitor 2] as a bar
graph. This parameter is only available with an LCD keypad.
100.0%
(0.0 - 100.0%)
o1-45
(11C5)
RUN
3rd Monitor Area Selection Sets the horizontal axis value used to display the monitor set in o1-26 [Custom Monitor 3] as a bar
graph. This parameter is only available with an LCD keypad.
0 : +/- Area ( - o1-46 ～ o1-46 )
1 : + Area ( 0 ~ o1-46 )
0
(0 - 1)
o1-46
(11C6)
RUN
3rd Monitor Area Setting Sets the horizontal axis value used to display the monitor set in o1-26 [Custom Monitor 3] as a bar
graph. This parameter is only available with an LCD keypad.
100.0%
(0.0 - 100.0%)
o1-47
(11C7)
RUN
Trend Plot 1 Scale Minimum
Value
Sets the horizontal axis minimum value used to display the monitor set in o1-24 [Custom Monitor 1]
as a trend plot. This parameter is only available with an LCD keypad.
-100.0%
(-300.0 - +299.9%)
o1-48
(11C8)
RUN
Trend Plot 1 Scale
Maximum Value
Sets the maximum value for the vertical axis used to display the monitor that was set in o1-24
[Custom Monitor 1] as a trend plot. This parameter is only available with an LCD keypad.
100.0%
(-299.9 - +300.0%)
To Next Page
Loading...
