10.2 Operation of Digital Operator
10.2.2 Operation of Utility Functions
10-11
ACC: Acceleration
Note: Refer to the following section for details on the acceleration rate.
7.3.4 Settings in the Program Table on page 7-13
DEC: Deceleration
Note: Refer to the following section for details on the deceleration rate.
7.3.4 Settings in the Program Table on page 7-13
POUT: Programmable Output Signals
Note: Refer to the following section for details on the programmable output signals.
7.3.4 Settings in the Program Table on page 7-13
EVENT: Pass Condition
Note: 1. Refer to the following section for details on the pass condition and elapsed time.
7.3.4 Settings in the Program Table on page 7-13
2. The default setting is EVT000 = IT00000.
㸿㹁㹁㸮㸮㸮㸻㸯㸰㸱㸲㸳㸴㸵㸶
㸿㹁㹁㸮㸮㸮㸻㸯㸰 㸱㸲㸳㸴㸵㸶
Move cursor Change acceleration
If the value becomes less than 1,
“:” is displayed.
㸿㹁㹁㸮㸮㸮㸻㸯㸱 㸱㸲㸳㸴㸵㸶
㹂㹃㹁㸮㸮㸮㸻㸯㸰㸱㸲㸳㸴㸵㸶
㹂㹃㹁㸮㸮㸮㸻㸯㸰 㸱㸲㸳㸴㸵㸶
Move cursor Change deceleration
㹂㹃㹁㸮㸮㸮㸻㸯㸱 㸱㸲㸳㸴㸵㸶
If the value becomes less than 1,
“:” is displayed.
㹎㹍㹓㹒㸮㸮㸮㸻㹌㸿㹘㸸㹌㸿㹘㸸
㹎㹍㹓㹒㸮㸮㸮㸻㹌㸿㹘㸸㹌㸿㹘㸸
Move cursor Change programmable output signal
Pressing the key changes the display
in the following order.
ࠉࠉ㹌Ѝ㸿Ѝ㹘Ѝ㸸
㹎㹍㹓㹒㸮㸮㸮㸻㹌㹌㹘㸸㹌㸿㹘㸸
Pressing the key changes the display
in the reverse order.
㹃㹔㹒㸮㸮㸮㸻㹒㸯㸰㸱㸲㸳 㹃㹔㹒㸮㸮㸮㸻㹒㸯㸰㸱㸲㸳
Move cursor
Move cursor
Move cursor
㹃㹔㹒㸮㸮㸮㸻㹇㹒㸯㸰㸱㸲㸳
㹃㹔㹒㸮㸮㸮㸻㹌㹒㸯㸰㸱㸲㸳
㹃㹔㹒㸮㸮㸮㸻㹂㹒㸯㸰㸱㸲㸳
㹃㹔㹒㸮㸮㸮㸻㹑㹃㹊㸮㹒㸯㸰㸱㸲㸳
㹃㹔㹒㸮㸮㸮㸻㹑㹃㹊㸯㹒㸯㸰㸱㸲㸳
㹃㹔㹒㸮㸮㸮㸻㹑㹃㹊㸵㹒㸯㸰㸱㸲㸳
㹃㹔㹒㸮㸮㸮㸻㸸
Change elapsed time
㹃㹔㹒㸮㸮㸮㸻㹒㸰㸰㸱㸲㸳
㹃㹔㹒㸮㸮㸮㸻㹇㹒㸯㸰㸱㸲㸳
㹃㹔㹒㸮㸮㸮㸻㹇㹒㸰㸰㸱㸲㸳
㹃㹔㹒㸮㸮㸮㸻㹌㹒㸯㸰㸱㸲㸳
㹃㹔㹒㸮㸮㸮㸻㹌㹒㸰㸰㸱㸲㸳
㹃㹔㹒㸮㸮㸮㸻㹂㹒㸯㸰㸱㸲㸳
㹃㹔㹒㸮㸮㸮㸻㹂㹒㸰㸰㸱㸲㸳
㹃㹔㹒㸮㸮㸮㸻㹑㹃㹊㸮㹒㸯㸰㸱㸲㸳
㹃㹔㹒㸮㸮㸮㸻㹑㹃㹊㸯㹒㸯㸰㸱㸲㸳
㹃㹔㹒㸮㸮㸮㸻㹑㹃㹊㸮㹒㸰㸰㸱㸲㸳
㹃㹔㹒㸮㸮㸮㸻㹑㹃㹊㸯㹒㸰㸰㸱㸲㸳
㹃㹔㹒㸮㸮㸮㸻㹑㹃㹊㸵㹒㸯㸰㸱㸲㸳
㹃㹔㹒㸮㸮㸮㸻㹑㹃㹊㸵㹒㸰㸰㸱㸲㸳
Change elapsed time
Change elapsed time
Change elapsed time
Change elapsed time
Change elapsed time
Change elapsed time
Change pass
condition
Move cursor
Change pass
condition
Move cursor
Change pass
condition
Move cursor
Change pass
condition
Move cursor
Change pass
condition
Change pass
condition
Change pass condition
To Next Page
Loading...
