10.2 Operation of Digital Operator
10.2.2 Operation of Utility Functions
10-12
LOOP: Number of Executions
Note: Refer to the following section for details on the number of executions.
7.3.4 Settings in the Program Table on page 7-13
NEXT: PGMSTEP to be Executed Next
Note: Refer to the following section for details on the program step to execute next.
7.3.4 Settings in the Program Table on page 7-13
Saving Program Tables
The operating procedure for saving program tables is shown below.
* If the key is pressed in an operation prohibited state, “Error.” is displayed for approximately 2 seconds and
then the display returns to the program table editing screen. In this case, make the setting again by referring to
Preparation.
Step Display after Operation Keys Operation
1 – Display the program table editing screen.
2
Press the key to view the program table
save operation screen.
3
Move the cursor with the keys to select
“STORE”.
Note: Selecting “CANCEL” and pressing the key
will return the display to the program table editing
screen.
4
Press the key to start saving the program
table to flash memory.*
Do not turn OFF the control power supply until
saving has been completed normally.
5–
When saving to flash memory has been com-
pleted normally, the display returns to the pro-
gram table editing screen.
6
Press the key to return to the Utility Function
Mode main menu.
㹊㹍㹍㹎㸮㸮㸮㸻㸮㸮㸮㸮㸯
㹊㹍㹍㹎㸮㸮㸮㸻㸮㸮㸮㸮㸯
Move cursor Change number of executions
㹊㹍㹍㹎㸮㸮㸮㸻㸮㸯㸮㸮㸯
㹌㹃㹖㹒㸮㸮㸮㸻㸮㸮㸮㸮㸮
㹌㹃㹖㹒㸮㸮㸮㸻㸮㸮㸮㸮㸮
Move cursor Change next PGMSTEP to be executed
㹌㹃㹖㹒㸮㸮㸮㸻㸮㸮㸰㸳㸳
If the value becomes less than 0,
“END” is displayed.
㹀㹀ࠉࠉࠉࠉࠉ㸫㹎㹅㹋ࠉ㹃㹢㹧㹲㸫
㹎㸮㸮㸮㸻㹑㹒㹍㹎
㹎㸮㸮㸯㸻㹑㹒㹍㹎
㹎㸮㸮㸰㸻㹑㹒㹍㹎
㹎㸮㸮㸱㸻㹑㹒㹍㹎
㧮㧮ޓޓޓޓޓ㧙㧼㧳㧹ޓ㧱㨐㨕㨠㧙
㧿㨀㧻㧾㧱ޓ㧼㧳㧹ޓ㨀㧭㧮㧸㧱㧫
ޓޓ㧯㧭㧺㧯㧱㧸ޓ㧿㨀㧻㧾㧱
㧮㧮ޓޓޓޓޓ㧙㧼㧳㧹ޓ㧱㨐㨕㨠㧙
㧿㨀㧻㧾㧱ޓ㧼㧳㧹ޓ㨀㧭㧮㧸㧱㧫
ޓޓ㧯㧭㧺㧯㧱㧸ޓ㧿㨀㧻㧾㧱
㧮㧮ޓޓޓޓޓ㧙㧼㧳㧹ޓ㧱㨐㨕㨠㧙
㧿㨠㨛㨞㨕㨚㨓ޓ㨚㨛㨣㧚㧚㧚
㧼㨘㨑㨍㨟㨑ޓ㨣㨍㨕㨠㧚
㧮㧮ޓޓޓޓޓ㧙㧼㧳㧹ޓ㧱㨐㨕㨠㧙
㧼㧻㧿㧜㧜㧜㧩㧿㨀㧻㧼
㧼㧻㧿㧜㧜㧝㧩㧿㨀㧻㧼
㧼㧻㧿㧜㧜㧞㧩㧿㨀㧻㧼
㧼㧻㧿㧜㧜㧟㧩㧿㨀㧻㧼
㹀㹀ࠉࠉࠉࠉࠉ㸫㹄㹓㹌㹁㹒㹇㹍㹌㸫
㹄㹬㸰㸮㸵ࠉ㹔㸫㹋㹭㹬㹧㹲㹭㹰
㹄㹬㸮㸴㸮ࠉ㹎㹅㹋ࠉ㹃㹢㹧㹲
㹄㹬㸮㸴㸯ࠉ㹘㹍㹌㹃ࠉ㹃㹢㹧㹲
㹄㹬㸮㸴㸰ࠉ㹈㹑㹎㹂ࠉ㹃㹢㹧㹲
To Next Page
Loading...
