10.2 Operation of Digital Operator
10.2.2 Operation of Utility Functions
10-18
ZONE Table Initialization (Fn064)
This function initializes ZONE tables and restores the default settings.
Preparation
The following conditions must be met to initialize ZONE tables.
• The write-prohibited setting (Fn010) must not be set to write-protect parameters.
• A ZONE table initialization must not be in progress for any means other than the digital oper-
ator.
Operating Procedure
* If the key is pressed in an operation prohibited state, “Error.” is displayed for approximately 2 seconds and
then the display returns to the Fn064 operation screen. In this case, make the setting again by referring to
Preparation.
Step Display after Operation Keys Operation
1
Press the key to open the Utility Function
Mode main menu, and move the cursor with the
keys to select Fn064.
2
Press the key to view the Fn064 operation
screen.
3
Press the key to start ZONE table initializa-
tion.*
Do not turn OFF the control power supply until
initialization has been completed normally.
To cancel the Fn064 operation, press the
key before pressing the key. The display
returns to the Utility Function Mode main menu
without executing the operation.
4 –
When ZONE table initialization has been com-
pleted normally, “Done.” is displayed.
5
Press the key to return to the Utility Function
Mode main menu.
㹀㹀ࠉࠉࠉࠉࠉ㸫㹄㹓㹌㹁㹒㹇㹍㹌㸫
㹄㹬㸮㸴㸱ࠉ㹎㹅㹋ࠉ㹇㹬㹧㹲
㹄㹬㸮㸴㸲ࠉ㹘㹍㹌㹃ࠉ㹇㹬㹧㹲
㹄㹬㸮㸴㸳ࠉ㹈㹑㹎㹂ࠉ㹇㹬㹧㹲
㧮㧮ޓޓޓޓ㧙㨆㧻㧺㧱ޓ㧵㨚㨕㨠㧙
ޓ㧿㨠㨍㨞㨠ޓ㧦㨇㧰㧭㨀㧭㨉
ޓ㧾㨑㨠㨡㨞㨚㧦㨇㧿㧱㨀㨉
㧮㧮ޓޓޓޓ㧙㨆㧻㧺㧱ޓ㧵㨚㨕㨠㧙
㧾㨑㨟㨠㨛㨞㨕㨚㨓ޓ㨚㨛㨣㧚㧚㧚
㧼㨘㨑㨍㨟㨑ޓ㨣㨍㨕㨠㧚
㧮㧮ޓޓޓޓ㧙㨆㧻㧺㧱ޓ㧵㨚㨕㨠㧙
㧰㨛㨚㨑㧚
㧼㨞㨑㨟㨟ޓ㨇㧿㧱㨀㨉ޓ㨗㨑㨥㧚
㹀㹀ࠉࠉࠉࠉࠉ㸫㹄㹓㹌㹁㹒㹇㹍㹌㸫
㹄㹬㸮㸴㸱ࠉ㹎㹅㹋ࠉ㹇㹬㹧㹲
㹄㹬㸮㸴㸲ࠉ㹘㹍㹌㹃ࠉ㹇㹬㹧㹲
㹄㹬㸮㸴㸳ࠉ㹈㹑㹎㹂ࠉ㹇㹬㹧㹲
To Next Page
Loading...
Need help?
General
