YASKAWA Sigma-V Series User Manual

3 Wiring and Connection
3.1.2 Main Circuit Wire
3-6
(2) Wire Sizes
The following table shows the symbols for the power input terminals, screw sizes for terminals, tightening
torque, wire sizes, and crimp terminals used for the SERVOPACKs and converters.
 For Three-phase, 200V
∗1. Use SERVOPACKs and converters in the specified combinations.
∗2. Use the crimp terminals that are recommended by Yaskawa or an equivalent.
Combination of SERVO-
PACK and Converter
*1
Terminal
Symbols
Screw Size
for Terminals
Tightening
Torque
(Nm)
HIV Wire Size in
mm
2
(AWG)
Crimp Terminal
Model
(Made by J.S.T.
Mfg Co., Ltd.)
*2
SGDV-121H
SGDV-
COA2BAA
SERVO-
PACK
P, N M8 15.0
Bus bar attached
to the converter
–
U, V, W M8 3.0 60 (2/0) R60-8
DU, DV, DW M6 3.0 5.5 (10) R5.5-6
M8 9.0 to 1.0 60 (2/0) R60-8
Converter
P, N M8 3 .0
Bus bar attached
to the converter
–
L1, L2, L3 M8 3.0 38 (1) R38-8
1, 2
M8 3.0 38 (1) R38-8
CN101
(L1C, L2C)
–
(Connector)
– 1.25 (16) –
B1, B2 M8 3.0 8 (8) R8-8
M8 9.0 to 11.0 38 (1) R38-8
SGDV-161H
SGDV-
COA3GAA
SERVO-
PACK
P, N M8 15.0
Bus bar attached
to the converter
–
U, V, W M8 3.0 100 (4/0) CB100-S8
DU, DV, DW M6 3.0 5.5 (10) R5.5-6
M8 9.0 to 11.0 100 (4/0) 100-8
Converter
P, N M10 12 to 20
Bus bar attached
to the converter
–
L1, L2, L3 M10 12 to 20 60 (2/0) R60-10
1, 2
M10 12 to 20 60 (2/0) R60-10
CN101
(L1C, L2C)
–
(Connector)
– 1.25 (16) –
B1, B2 M10 12 to 20 14 (6) R14-10
M8 9.0 to 11.0 60 (2/0) R60-8
SGDV-201H
SGDV-
COA3GAA
SERVO-
PACK
P, N M10 12 to 20
Bus bar attached
to the converter
–
U, V, W M10 30.0 100 (4/0) R100-10
DU, DV, DW M6 3.0 5.5 (10) R5.5-6
M8 9.0 to 11.0 100 (4/0) 100-8
Converter
P, N M10 12 to 20
Bus bar attached
to the converter
–
L1, L2, L3 M10 12 to 20 100 (4/0) R100-10
1, 2
M10 12 to 20 100 (4/0) R100-10
CN101
(L1C, L2C)
–
(Connector)
– 1.25 (16) –
B1, B2 M10 12 to 20 14 (6) R14-10
M8 9.0 to 11.0 100 (4/0) 100-8

YASKAWA Sigma-V Series Specifications

General

Brand	YASKAWA
Model	Sigma-V Series
Category	Servo Drives
Language	English