(2)
STEREOIMONO
--
This switches the output between
stereo and mono. The same signals
are
output when set
to
MONO, even when separate cables
are
connected to the left
and right OUTPUT terminals.
When the output mode is set
to
MONO, the signals of the
effect module outputs
are
mixed and are the same for the left
and right channels, even when the
final
output of effect mod-
ule is
in
stereo. This setting is convenient especially when
two outputs of the same signals are required, such
as
in feed-
ing the same signal
to
a
PA
and a monitor system.
When the final effect module's output is stereo and the output
mode parameter above is set
to
STEREO, the left and right
channels are not mixed, and a cable connected to the
L/MONO
output terminal receives only the left channel out-
put"
Functions
of
the Panel Keys
UTILITY
key
--
Moves to the second page (Patch name).
DEC
VDNC
A
keys
--
Change the parameter settings.
EDIT
<
/
>
keys
--
Move the cursor.
2. Naming Patches
UTY2
PATCH
NAMING
BS
[ULTRA
SUPERCHJ
This page lets you name the Patch which was previously
selected in the Play mode. Names can
be
up to fifteen char-
acters in length. Available characters (letters and numbers)
are shown below.
012345678
9
(Space)
ABCDEFGHI
JKLMNOPQRSTUVWXY
Z
(Space)
abcdef
ghi
j
klmnopqrstuvwxyz
(Space)
@!?$Y•’%&"'
0,
4
(Space)
Move the cursor (indicated
as
an
underline in the
FL
display)
by
using the EDIT
c
/
>
keys, and select characters
by
using
either the DEC V/INC
A
keys or Data Entry Control
2.
select the appropriate function (either delete or insert; the
selected function is displayed at the bottom left of the
display) by using Data Entry Control
1,
then press the
STORE/EXECUTE key to execute.
BS
(Backspace)
--
This deletes the character preceding the
cursor, and
all
characters and spaces following the cursor are
moved one to the left to close the space. When selected,
backspace is executed
by
pressing the STOREfEXECUTE
key.
MS
(Insert)
--
This inserts
a
space at the cursor position,
and all characters and spaces following the cursor are moved
to
the right. When selected, insert is executed by pressing
the STORE/EXECUTE key.
DEL
(Delete)
--
This deletes the character at the cursor
position, and all characters and spaces following the cursor
are moved one to the left to close the space. When selected,
delete
is
executed by pressing the STORE/EXECUTE
key.
Functions of the Panel Keys
UTILITY
key
--
Moves to page
3-1
(Selecting the
MIDI
Channel).
Data Entry Control
l
--
Selects the function which is
to
be
executed
by
the STORE/EXECUTE key.
Data Entry Control
2
--
Selects characters.
DEC VDNC
A
keys
--
Select characters.
EDIT
c
/
>
keys
--
Move the cursor.
STORE/EXECUTE key
--
Executes backspace
or
insert
functions.
Helpful Hint:
When changing the name of Patch, select the Patch in the
Play mode then call up this page. (You
can
only change the
names of Patches that are in the edit buffer.)
Note:
The Patch name is one of the Patch parameters. Therefore, it
is necessary to store the Patch
to
memory in order to confirm
the change of the Patch name.
When the Patch name has
been changed, return
to
the Play mode
("B
",
which means
that the Patch is being edited, appears in the
FL
display),
then store it
to
memory. See page
17
for information on stor-
ing.
You can delete or insert characters by using the
STORE/EXECUTE key.
To delete or insert a character,
To Next Page
Loading...
