Index
Index-1
Numerics
2-port error corrections, performing,
6-42, 6-71
4 Param Displays softkey, 1-18
A
aborting a print or plot process, 4-31
absolute
ripple test value, 1-92, 1-93
absolute power, 6-39
accuracy, 1-59
accuracy and input power, 7-89
accuracy enhancement, 7-8, 7-39, 7-53
accurate measurements of electrically
long devices
cause of measurement problems, 5-7
improving measurement results, 5-7
activating
averaging, 5-15
chop sweep mode, 5-12
display markers, 1-25
fixed markers, 1-29
limit test, 1-82
activating the bandwidth test, 1-97
active channel display, 1-11
adapter removal, 6-41
adapter removal calibration (ECal),
6-69–??
adapters
minimizing error, 6-47
adapters, matched, 6-45
ADC, 7-7
address menu, 7-80
addressing two sources, 2-29
adjusting
display colors, 1-22
relative velocity factor, 3-12
AmiPro, using, 4-21
amplifiers, measuring, 1-54
amplitude tracking, 2-38
amplitude, tracking, 1-42
analog in menu, 7-23
analyzer display formats, 7-25
group delay format, 7-27
group delay principles, 7-32
imaginary format, 7-32
linear magnitude format, 7-30
log magnitude format, 7-25
phase format, 7-26
polar format, 7-29
real format, 7-31
smith chart format, 7-28
SWR format, 7-31
analyzer internal memory, what you can
save
, 4-34
applying power, 8-5
arrays
format, 7-9
pre-raw data, 7-8
raw, 7-8
ASCII data formats, 4-39
CITIfile, 4-39
S2P data format, 4-40
assigning standards to various TRL
classes
, 6-51
assigning standards to various TRM
classes
, 6-55
attenuator, 7-14
attenuator, repetitive switching, 7-14
attenuator, source step, 7-4
auto sweep time mode, 7-12
auto sweep time mode, setting, 5-11
auto-feed, selecting, 4-13
automatic mode, 7-10
autostarting sequences, 1-109
averaging, 7-36
isolation, 6-60
averaging factor, reducing, 5-11
averaging, activating, 5-15
averaging, sweep to sweep, 7-7
B
band
adding a frequency, 1-89
changing a frequency, 1-88
deleting a frequency, 1-90
frequency, 1-87
bandwidth, 1-97
bandwidth markers
displaying, 1-98
bandwidth test
activating, 1-97
running, 1-97–1-100
setting up limits, 1-95–1-97
bandwidth testing, 1-95–1-100
bandwidth value
displaying, 1-99
bandwidth, searching for, 1-42
basic measurements, making, 1-4
bilateral device, 6-22, 6-25
blanking the display, 1-21
block, receiver, 7-4
built-in synthesized source, 7-4
source step attenuator, 7-4
built-in test set, 7-4
C
cables, interconnecting, 5-4
calculating statistics of measurement
data
, 1-43
calculations, ratio, 7-7
calibrating for non-coaxial devices, 6-50
TRL error-correction, 6-50
TRM error correction, 6-54
calibrating for noninsertable devices,
6-40
adapter removal, 6-41, 6-69
matched adapters, 6-45
modifying the cal kit through
definition, 6-46
calibrating the analyzer receiver to
measure absolute power
, 6-39
calibration
ECal, 6-58–6-68
electronic. See ECal
power meter, 2-12
calibration considerations, 6-4
calibration standards, 6-5
clarifying type-N connector sex, 6-4
device measurements, 6-4
error-correction stimulus state, 6-9
frequency response of calibration
standards
, 6-6
interpolated error correction, 6-8
measurement parameters, 6-4
omitting isolation calibration, 6-4
restarting a calibration, 6-5
saving calibration data, 6-5
calibration data, saving, 6-5, 7-66
calibration kit menu, 7-59
defining standard menus, 7-60
label class menu, 7-66
label kit menu, 7-66
label standard menu, 7-63
specify class menu, 7-63
specifying offset menu, 7-62
calibration kit, saving a modified, 7-66
calibration kits, modifying, 7-58
calibration routines, 7-56
full two-port calibration, 7-57
response and isolation calibration,
7-56
response calibration, 7-56
S11 and S22 one-port calibration, 7-57
TRL*/LRM* two-port calibration, 7-57
calibration standards, 6-5
calibration techniques
improper, 5-4
calibration, measurement, 7-39
calibration, receiver, 6-15
calibration, TRL*/LRM*, 7-68
calling the next measurement sequence,
2-29
capabilities
mixer measurement, 2-3
capacitance, fringe, 6-7
cause of measurement problems, 5-7
center frequency, setting, 1-36
changing
sequence title, 1-105
system bandwidth, 5-15
To Next Page
Loading...
Need help?
General
