Type DC 1200 DC 2000 DC 2100 DC 2900
Carrier weight class
1 15 - 25 t
33,000 -
55,000 lbs
20 - 35 t
44,000 -
77,000 lbs
25 - 40 t
55,000 -
88,000 lbs
35 - 55 t
77,000 -
120,000 lbs
Service weight
2 1,200 kg
2,160 lbs
2,000 kg
4,400 lbs
2,100 kg
4,630 lbs
2,900 kg
6,400 lbs
Weight without adapter
3 980 kg
2,205 lbs
1,750 kg
3,858 lbs
1,850 kg
4,079 lbs
2,600 kg
5,732 lbs
Dimensions
Total length
Total width of cutting head
Diameter of cutter drum
1,250 mm
49.21 in.
800 mm
31.30 in.
585 mm
23.03 in.
1,425 mm
56.10 in.
880 mm
34.65 in.
720 mm
28.35 in.
1,425 mm
56.10 in.
1,000 mm
39.39 in.
720 mm
28.35 in.
1,600 mm
62.99 in.
1,250 mm
49.21 in.
720 mm
28.35 in.
Nominal power 80 kW
107 hp
120 kW
161 hp
120 kW
161 hp
160 kW
215 hp
Oil flow rate (see chapter Appendix)
Operating pressure (see chapter Appendix)
Rotational speed 40 - 110 rpm 45 - 105 rpm 35 - 80 rpm 35 - 80 rpm
Pick speed 1.3 - 3.3 m/s
4.1 - 10.9 fps
1.5 - 3.6 m/s
4.9 - 11.7 fps
1.1 - 2.7 m/s
3.7 - 8.8 fps
1.3 - 3.0 m/s
4.2 - 9.9 fps
Number of picks 44 44 48 56
Pick shaft diameter 30 mm
1.18 in.
30 mm
1.18 in.
30 mm
1.18 in.
30 mm
1.18 in.
Maximum cutting force at 350 bar (5,075 psi) 43.8 kN
9,839 lbf
52.3 kN
11,730 lbf
69.8 kN
15,694 lbf
77.3 kN
17,380 lbf
Maximum torque at 350 bar (5,075 psi) 12.8 kNm
9,426 ft lbs
17.5 kNm
12,914 ft lbs
23.4 kNm
17,249 ft lbs
27.8 kNm
20,528 ft lbs
Maximum rock hardness 60 Mpa
8,700 psi
70 Mpa
10,150 psi
80 Mpa
11,600 psi
100 Mpa
14,500 psi
Gear oil volume 15 l
3.96 gal
25 l
6.60 gal
30 l
7.92 gal
47 l
12.41 gal
Oil volume hydraulic motor 3 l
0.79 gal
5 l
1.32 gal
5 l
1.32 gal
6 l
1.58 gal
Hydraulic connections (Transverse drum cutter)
Pressure / tank line
Leakage oil line
SAE 3/4"
6000 psi
JIC 1 1/16"
JIC 1 5/16"
JIC 1 1/16"
Hose lines (inside diameter)
Pressure / tank line
Leakage oil line
19 mm
(0.75 in.)
19 mm
(0.75 in.)
25 mm (1.0 in.)
19 mm (0.75 in.)
Hole pattern MB 1700 HB 2000
Part number 3363 1197 50 3363 1155 33 3363 1155 34 3363 1155 35
1
Weight applies to standard carriers only.
Any variations must be agreed with Atlas Copco and / or the carrier manufacturer.
2
transverse drum cutter including adapter plate of medium size
Please note that the working weight can be considerably higher, depending on the adapter plate.
3
transverse drum cutter including rotatable upper part. Accessory parts such as the adapter plate are not included.
DC 200, 400, 600, 1000, 1200, 2000, 2100, 2900 Safety and operating instructions
© Construction Tools GmbH | 3390 5192 01 | 2016-12-01
Original instructions
65
To Next Page
Loading...