Barco HDX - Mounting the Lamp Cover

To Next Page

To Previous Page

16. Servicing

Image 16-10

Lamp side cover

2. Take off the side cover.

16.7 Mounting the lamp cover

WARNING: Switch off the projector and unplug the power cord before starting the procedure.

Necessary tools

7mmﬂat screw driver

How to mount

1. Place the front cover on the is place and secure the 6 captive screws.

300

R5905032 HDX SERIES 20/11/2014

Main Page

Default Chapter5
- Table of Contents5
1 Safety11
- General Considerations11
  - General Safety Instructions11
  - Notice on Safety11
- Important Safety Instructions12
- Important Warnings Concerning HDX Flight Cases14
2 General17
- Installation Requirements17
- Projector Weight18
- Unpacking the Projector18
- Initial Inspection19
- Box Content19
- HDX Flight Case20
- Projector Conﬁgurations20
  - Rear Projection21
  - Positioning the Projector22
- Projector Air Inlets and Outlets24
- Free Download of Projector Toolset24
- Installation Process Overview25
- Quick Setup25
3 Physical Installation27
- Remote Control Unit (RCU)27
- Lenses31
- Connecting the Projector with the Power Net42
- Alignment of a Table Mounted Projector43
- Mounting the Bottom Carry Handler43
- Mounting the Top Carry Handler45
- Suspension of the Projector with Rigging Clamps46
- Alignment of a Ceiling Mounted Projector48
4 Input & Communication51
- Introduction51
- Input Source Connections52
- Communication Connections54
- Utility-Accessory Outlet57
5 Getting Started59
- RCU & Local Keypad59
- Terminology Overview59
- Power on Projector61
- Software Overview63
- Switching to Standby64
- Power off Projector64
- Status Leds65
- Using the RCU65
- Projector Address67
- Source Selection67
6 Quick Set up Adjustment69
- Text Boxes on or off69
- Quick Lens Adjustment Via LENS Key69
- Direct Lens Adjustment (RCU)71
- Quick Picture in Picture72
- Quick Language Selection72
7 Start up of the Adjustment Mode75
- About the Adjustment Mode75
- About the Use of the Remote Control and the Local Keypad75
- Start up the Adjustment Mode75
- Navigation and Adjustments76
- Menu Memory77
- Shortcut Keys to the Menus77
- Test Patterns in Adjustment Mode78
- Help Information in Adjustment Mode78
8 Input79
- Input Menu Overview79
- Input Selection80
- Advanced Settings81
- Input Locking85
- Minimum Delay86
- Native Resolution87
- No Signal88
- Edid92
- Input97
9 Image109
- Image Menu Overview109
- Start up the Image Adjustments110
- Image Settings110
- Aspect Ratio122
- Timings124
  - Source Timings124
  - Advanced Timings, Clamp Delay - Clamp Width125
- Image File Services127
- Save Custom Settings135
- What Can be Done135
- Splash Image136
10 Layout139
- Layout Menu Overview139
- Introduction139
- Main Window140
- Pip Window143
- Layout File Services149
- Lens Behavior154
11 Lamp157
- Lamp Menu Overview157
- Lamp Power Mode157
- Hush Kit Activate/Deactivate158
- Lamp Power159
- Auto Dimming When on Pause160
- Auto Dimming When no Signal161
- Auto Dimming When Over-Temperature162
- CLO Mode (Constant Light Output Mode)163
- CLO Targets165
- LPS Power165
- How to Display166
- Lamp Identiﬁcation166
- Z-Axis Adjustment167
12 Alignment169
- Alignment Menu Overview169
- Orientation170
- Lens Adjustment, Zoom - Focus171
- Lens Adjustment, Shift172
- Lens Adjustment, MID Position173
- Calbrate Lens at Startup174
- Calibrate Lens174
- Warping175
- Blanking Adjustment198
- Contrast-Intensity200
- Gamma201
- Internal Patterns201
- Color Space203
- What Can be Adjusted203
- Scenergix205
- Glasses217
13 Projector Control223
- Projector Control Menu Overview223
- Individual Projector Address224
- Projector Common Address225
- Serial Communication226
  - Baud Rate Setup226
  - Interface Standard226
- Network227
- IR Control Switching241
- DMX242
- Buttons252
  - Standby Button252
  - Shortcut Keys253
- Menu Position254
- Local LCD254
- Language Selection255
- Scheduler256
- GSM Conﬁguration, Activation263
- GSM Conﬁguration, Subscription265
- FLEX, Light Output Conﬁguration267
- SMS Services269
14 Service271
- Service Menu Overview271
- Identiﬁcation272
- What Can be Seen272
- Diagnosis273
- Internal Service Patterns281
- Convergence285
- Factory Defaults286
- USB Memory287
- Reset Formatter289
- Reﬁll Mode289
- Save Custom Settings290
- Special HD Camera Mode291
- Auto Dimming When Over-Temperature292
- Time and Date293
15 Maintenance295
- Cleaning the Lens295
- Cleaning the Exterior of the Projector295
16 Servicing297
- Inserting an Input Module297
- Removal of the Lamp House298
- Installation of the Lamp House299
- Removal of the300
- Mounting the302
- Removal of the Lamp Cover303
- Mounting the Lamp Cover304
- Replacement of the High Density Dust Filter305
- Remove and Clear Metal Front Filter306
- How to Install307
Dimensions309
- Dimensions of a HDX Projector309
Speciﬁcations311
- Speciﬁcations of the HDX W12311
- Speciﬁcations of the HDX W14312
- Speciﬁcations of the HDX W18313
- Speciﬁcations of the HDX W20 FLEX314
Standard Source Files317
- Table Overview317
DMX Chart321
- DMX Chart, Basic321
- DMX Chart, Full321
- DMX Chart, Extended322
Stacking HDX Projectors325
- Mount Stacking Points325
- Aligning Stacked HDX Projectors328
Environmental Information331
- Disposal Information331
- Rohs Compliance331
- Production Address333
Index335

Barco HDX - Mounting the Lamp Cover

Table of Contents

Related product manuals