Account # Enter the Customer Code for the Contact
ID and SIA protocols: ask the Central Station.
Default: 0000.
Communication Protocol Select the protocol speci
-
fied by the Central Station:
Ø
SIA over FIBRO;
Ø
Contact ID over FIBRO.
Default: Contact ID over FIBRO.
SIA Code for Panel Lost Event Enter the SIA Event
code that must be sent when the GSM module cannot
communicate with the Control Panel.
Default: 00.
CID Code for Panel Lost Event Enter the Contact ID
Event code that must be sent when the GSM module
cannot communicate with the Control Panel.
Default: 000.
GSM Network Fault Delay Set how long the GSM net
-
work must be faulty before a GSM Link Lost event is
triggered and a GSM network failure is reported. If the
GSM network is restored before the end of the pro
-
grammed time, the event has NOT occurred and the fault
is NOT reported. The GSM Net Fail event is still stored in
the Event Log however.
Valid entries: from 0 (delay disabled) to 255 minutes.
Default: 0.
GPRS Network Fault Delay Set how long the GPRS
network must be faulty before a GSM - Cellular Net-
work Fault event is triggered and a GPRS network fail-
ure is reported. If the GPRS network is restored before
the end of the programmed time, the event has NOT oc-
curred and the fault is NOT reported. The Data Network
Lost event is still stored in the Event Log however.
Valid entries: from 0 (delay disabled) to 255 minutes.
Default: 0.
Receiver 1 IP Address (Receiver 2 IP Address) En
-
ter the IP address of the Main (Backup) receiver pro
-
vided by the Central Station.
Default: 0.0.0.0.
+
The Receiver 2 IP Address is locked until the
Main Receiver APN is entered.
Receiver 1 Remote Port (Receiver 2 Remote Port)
Enter the Port number of the Main (Backup) Receiver
provided by the Central Station.
Default: 3061.
+
The Receiver 2 Remote Port is locked until the
Main Receiver APN is entered.
Main Receiver APN (APN 2) Enter the APN (Access
Point Name) for the Main (Backup) Receiver supplied
by the operator that provides the GPRS service.
Default: None.
+
Enter the correct APN for WAP/GPRS services or
some features may be limited (for more information,
please contact the operator of the service center).
+
The Main Receiver APN is the same as the
App/BOSS APN.
+
APN 2 is locked until the Main Receiver APN is
entered.
Main Receiver User Name (APN 2 Username) If re
-
quired, enter the Username for the Main (Backup) re
-
ceiver supplied by the operator that provides the GPRS
service.
Default: None.
+
The Main Receiver User name is the same as the
App/BOSS Username.
+
The APN 2 Username is locked until the Main Re
-
ceiver APN is entered.
Main Receiver Password (APN 2 Password) If re
-
quired, enter the Password for the Main (Backup) re
-
ceiver supplied by the operator that provides the GPRS
service.
Default: None.
+
The Main Receiver Password is the same as the
App/BOSS Password.
+
The APN 2 Password is locked until the Main Re-
ceiver APN is entered.
Supervision 1 Enabled (Supervision 2 Enabled) If
enabled, the GSM module periodically sends a Supervi-
sion Event to the Control Station and if it doesn’t receive
a response it generates a System > GSM Receiver 1
Lost (GSM receiver 2 Lost) Event.
Default: disabled.
+
The Supervision 1 Enabled (Supervision 2 En
-
abled) option is locked until the Main Receiver
APN (APN 2) is entered.
Supervision time 1 (Supervision time 2) Enter the
interval between an event and the subsequent supervi
-
sion event.
Valid entries: 60 to 65,535 seconds.
Default: 60 seconds.
+
The Supervision time 1 (Supervision time 2)op
-
tion is locked until the Main Receiver APN (APN 2)
is entered.
n
Disabling event transmission to the receivers
To disable the transmission of events to a receiver:
Ø
enter 0.0.0.0 for the IP address, or
Ø
set the remote port to 0, or
Ø
set a blank APN.
+
The last option is recommended ONLY for dis
-
abling the Backup receiver since the Main receiver
APN is the same one used by the APP/BOSS on
the GPRS.
80 Expandable Hybrid Control Panel
To Next Page