Page 14
The new code will now be displayed
To replace a code simply enter the new code in the same address as the old code. This will overwrite the previous
code but maintain the user permissions as mapped to that user number by its group number.
To clear or delete a code simply press and hold the “CONTROL” button followed within 2 seconds by “0” button at the
address where the old code is stored.
e.g. P 3 E <CONTROL> then <0> E
3 beeps
USER CODE GROUP NUMBER P101E—P200E
Each User code is assigned a User Code Group number from 1-20. The User Code groups assign the Areas and
Arm/Disarm parameters plus many other options to each User. The groups are fully programmable allowing full
control of what activities various Users may perform.
Addresses P101E-P200E relate to Users 1-100. A value of 1-20 is assigned at each address associated with a User.
If the User has a group number of 0 they are not allowed to perform any functions. Each User group consists of a
combination of 46 different options (split into 7 blocks of 8) as detailed below.
USER GROUPS 1-20 ARM/DISARM OPTIONS P201E-P220E
The first set of options for the User groups assigns the Areas that each group is allowed to Arm or Disarm as well as
whether is can Arm/Disarm the full alarm or Stay Mode or both. If the group is required to allow direct output control
(see P281E-P320E), all of these options must be turned off for the output programming to work.
P201E User Arm/Disarm Options for Group #1 - Default 1-8 OPTIONS
P202E User Arm/Disarm Options for Group #2 - Default 1,5,6 1 = Area "A"
P203E User Arm/Disarm Options for Group #3 - Default 1,5,6 2 = Area "B"
P204E User Arm/Disarm Options for Group #4 - Default 1,5,6 3 = Area "C"
P205E User Arm/Disarm Options for Group #5 - Default 1,5,6 4 = Area "D"
P206E User Arm/Disarm Options for Group #6 - Default 1,5,6 5 = Code can arm
P207E User Arm/Disarm Options for Group #7 - Default 1,5,6 6 = Code can disarm
P208E User Arm/Disarm Options for Group #8 - Default 1,5,6 7 = Code can arm stay mode
P209E User Arm/Disarm Options for Group #9 - Default 1,5,6 8 = Code can disarm stay mode
P210E User Arm/Disarm Options for Group #10 - Default 1,5,6
P211E User Arm/Disarm Options for Group #11 - Default 1,5,6
P212E User Arm/Disarm Options for Group #12 - Default 1,5,6
P213E User Arm/Disarm Options for Group #13 - Default 1,5,6
P214E User Arm/Disarm Options for Group #14 - Default 1,5,6
P215E User Arm/Disarm Options for Group #15 - Default 1,5,6
P216E User Arm/Disarm Options for Group #16 - Default 1,5,6
P217E User Arm/Disarm Options for Group #17 - Default 1,5,6
P218E User Arm/Disarm Options for Group #18 - Default 1,5,6
P219E User Arm/Disarm Options for Group #19 - Default 1,5,6
P220E User Arm/Disarm Options for Group #20 - Default 1,5,6
USER GROUPS 1-20 MISCELLANEOUS OPTIONS P221E-P240E
The Miscellaneous User group options allow the User to gain access to Client Program Mode to perform various
program functions. If the User is not to have access to Client Mode at all then all options at this address must be off.
P221E User Group #1 Miscellaneous Options - Default 1-7 OPTIONS
P222E User Group #2 Miscellaneous Options - Default 5 1 = Can change telephone #’s
P223E User Group #3 Miscellaneous Options - Default 5 2 = Can change Clock
P224E User Group #4 Miscellaneous Options - Default 5 3 = Can Print Event Memory
P225E User Group #5 Miscellaneous Options - Default 5 4 = Can Answer an In-coming call
P226E User Group #6 Miscellaneous Options - Default 5 5 = Can change Their Code
P227E User Group #7 Miscellaneous Options - Default 5 6 = Can change All Codes
P228E User Group #8 Miscellaneous Options - Default 5 7 = Allow access to Installer Mode
P229E User Group #9 Miscellaneous Options - Default 5 8 = Child Unset Warning
P230E User Group #10 Miscellaneous Options - Default 5
P231E User Group #11 Miscellaneous Options - Default 5
P232E User Group #12 Miscellaneous Options - Default 5
To Next Page
Loading...
