Page 44
RECORDING STATUS MESSAGES
The Customised Local PA and Command Control messages are recorded using the on-board microphone and
played back via the on-board speaker. You can program up 47 customised messages which can each be up to 10
seconds long. Before starting to record the customised messages first decide what they will be and have the text for
each message ready. Also number these messages from 1 to a maximum of number 47 and have this list ready as
you will need to assign the messages to the various functions later.
P890E 1-47E Record the Customised speech messages - To record message number one press P890E1E.
After the second “E” (enter) button has been pressed start talking clearly into the microphone from
a distance of about 150mm talking at normal speech level. Ensure that the message is shorter
than 10 seconds long and when the message is finished press the “E” (enter) button to terminate
recording of that message. Repeat the process until all messages have been recorded.
PLAYING BACK RECORDED STATUS MESSAGES
Once the Customised messages have been recorded you can play them back individually to verify the content.
P900E 1-47E Playback the Customised speech messages - To play back the recorded messages press
P900E followed by the message number then “E”. If you wish to play back another message
following the end of the first selection you only have to enter in a new message number then
“E” (enter). You can continue to do this until the “P” (program) button is next pressed.
SETTING PLAY-BACK VOLUME
When playing back the Customised or canned messages it is possible to set the audio volume level while in installer
program mode. The setting is adjustable in 8 steps ranging from 0-7 where 0 = High and 7 = Low volume. From the
keypad in normal operating mode the volume can also be adjusted by the User, using the “Control” button and either
the “6” or “9” buttons. By holding down the “Control” button and then pressing the “6” button repeatedly the volume is
increased. Using “Control” and the “9” button will decrease the volume.
P860E 0-7E Setting Playback Volume - Enter in a value from 0-7 with 0 = highest volume.
SELECTING THE CUSTOMISED “ARM” MESSAGE
If the following addresses are left blank i.e. “0”, the panel will assume that there is no custom voice message for this
Command Control & local PA function and revert to the canned message if programmed to do so.
P861E # E Area “A” Arm message number - This is the customised message number to play when Area
“A” is armed either locally or remotely by Command Control.
P862E # E Area “B” Arm message number - This is the customised message number to play when Area
“B” is armed either locally or remotely by Command Control.
P863E # E Area “C” Arm message number - This is the customised message number to play when Area
“C” is armed either locally or remotely by Command Control.
P864E # E Area “D” Arm message number - This is the customised message number to play when Area
“D” is armed either locally or remotely by Command Control.
SELECTING THE CUSTOMISED “DISARM” MESSAGE
If the following addresses are left blank i.e. “0”, the panel will assume that there is no custom voice message for this
Command Control & local PA function and revert to the canned message if programmed to do so.
P865E # E Area “A” Disarm message number - This is the customised message number to play when
Area “A” is disarmed either locally or remotely by Command Control.
P866E # E Area “B” Disarm message number - This is the customised message number to play when
Area “B” is disarmed either locally or remotely by Command Control.
P867E # E Area “C” Disarm message number - This is the customised message number to play when
Area “C” is disarmed either locally or remotely by Command Control.
P868E # E Area “D” Disarm message number - This is the customised message number to play when
Area “D” is disarmed either locally or remotely by Command Control.
To Next Page
Loading...
