Page 45
SELECTING THE CUSTOMISED “STAY” MODE “ARM” MESSAGE
If the following addresses are left blank i.e. “0”, the panel will assume that there is no custom voice message for this
Local PA only function and revert to the canned message if programmed to do so.
P869E # E Area “A” Stay Mode Arm message number - This is the customised PA message number to
play when Area “A” is armed in Stay mode locally.
P870E # E Area “B” Stay Mode Arm message number - This is the customised PA message number to
play when Area “B” is armed in Stay mode locally.
P871E # E Area “C” Stay Mode Arm message number - This is the customised PA message number to
play when Area “C” is armed in Stay mode locally.
P872E # E Area “D” Stay Mode Arm message number - This is the customised PA message number to
play when Area “D” is armed in Stay mode locally.
SELECTING CUSTOMISED “ON” MESSAGES FOR “OUTPUTS”
If the ON message number is left blank i.e. “0”, the panel will assume that there is no custom voice message for this
Command Control & local PA function and revert to the canned message if programmed to do so.
P891E # E Output #1 ON message number - This is the customised message number to play when Output
#1 turns ON either locally or remotely by Command Control.
P892E # E Output #2 ON message number - This is the customised message number to play when Output
#2 turns ON either locally or remotely by Command Control.
P893E # E Output #3 ON message number - This is the customised message number to play when Output
#3 turns ON either locally or remotely by Command Control.
P894E # E Output #4 ON message number - This is the customised message number to play when Output
#4 turns ON either locally or remotely by Command Control.
P895E # E Output #5 ON message number - This is the customised message number to play when Output
#5 turns ON either locally or remotely by Command Control.
P896E # E Output #6 ON message number - This is the customised message number to play when Output
#6 turns ON either locally or remotely by Command Control.
P897E # E Output #7 ON message number - This is the customised message number to play when Output
#7 turns ON either locally or remotely by Command Control.
P898E # E Output #8 ON message number - This is the customised message number to play when Output
#8 turns ON either locally or remotely by Command Control.
SELECTING CUSTOMISED “OFF” MESSAGES FOR “OUTPUTS”
If the OFF message number is left blank i.e. “0”, the panel will assume that there is no custom voice message for this
Command Control & local PA function and revert to the canned message if programmed to do so.
P901E # E Output #1 OFF message number - This is the customised message number to play when Output
#1 turns OFF either locally or remotely by Command Control.
P902E # E Output #2 OFF message number - This is the customised message number to play when Output
#2 turns OFF either locally or remotely by Command Control.
P903E # E Output #3 OFF message number - This is the customised message number to play when Output
#3 turns OFF either locally or remotely by Command Control.
P904E # E Output #4 OFF message number - This is the customised message number to play when Output
#4 turns OFF either locally or remotely by Command Control.
P905E # E Output #5 OFF message number - This is the customised message number to play when Output
#5 turns OFF either locally or remotely by Command Control.
P906E # E Output #6 OFF message number - This is the customised message number to play when Output
#6 turns OFF either locally or remotely by Command Control.
P907E # E Output #7 OFF message number - This is the customised message number to play when Output
#7 turns OFF either locally or remotely by Command Control.
P908E # E Output #8 OFF message number - This is the customised message number to play when Output
#8 turns OFF either locally or remotely by Command Control.
To Next Page
Loading...
