Page 26
button, i.e. no code is required. If this option is on, a valid Area "A" user code is required to arm the
area.
Option 5 Code required to bypass zones - If this option is off all zones associated with the areas assigned to
the keypad can be bypassed by anyone, i.e. no code is required. If this option is on, a valid Area "A"
user code must be entered following pressing of the bypass button to allow any zone bypasses to occur.
Also, only zones associated with the areas assigned to the user code can be bypassed in this mode.
Option 6 Chime Button disables "Day/Chime" mode - If this option is enabled, pressing the CHIME button for
two seconds will disable the day alarms for the area assigned to the keypad. When the day alarms
disable mode is active the “CHIME OFF” message will appear on the LCD display. To restore the day
function simply press the CHIME button again. If the option is disabled (option Off) then the chime button
is disabled.
Option 6 Repeat Current System alarm PA messages when Arming or Disarming - If this option is enabled,
and a system alarm is still current (e.g. the Mains Voltage is OFF), the current alarm will be re-played
over the internal speaker when Area A is armed or disarmed to alert the User that the problem still exits.
Note: P630E is the same as above but applies to Area B Keypad options
Note: P730E is the same as above but applies to Area C Keypad options
Note: P830E is the same as above but applies to Area D Keypad options
AREA "A" MISCELLANEOUS SPECIAL OPTIONS - P531E
AREA "B" MISCELLANEOUS SPECIAL OPTIONS - P631E
AREA "C" MISCELLANEOUS SPECIAL OPTIONS - P731E
AREA "D" MISCELLANEOUS SPECIAL OPTIONS - P831E
P531E 1E = Key-switch Input enabled
2E = Use 2nd Key-switch
3E = Key-switch is used for Arm or Stay
4E = Pendant chirps on Arming / disarming
5E = Pendant chirps on Stay Mode on / off
6E = 2 second output on Arming
7E = 2 second output on Disarming
8E = Spare
Option 1 Key-switch Input enabled - This option will enable the Key-switch input. The key-switch function is
provided on the System tamper input using a 4k7 resistor in the type 3 or 4 zone wiring configuration
(refer to the zone drawing on page 7). Operating the Key-switch input will arm Area "A" as determined
by P601E option 7.
Option 2 Use 2nd Key-switch - This option will enable dual end of line configuration of the Tamper/Key-switch
input and assign the high value end-of-line resistor (8k2) to Area "A" (refer to the zone drawing on page
7 Type 3 or 4). Operating the Key-switch input will arm Area "A" as determined by P601E option 8.
Option 3 Key-switch is used for Arm or Stay - If this option is on, operating the Key-switch will arm/disarm Area
"A". If this option is off, operating the Key-switch will turn Area "A" Stay Mode on and off.
Option 4 Pendant Chirps on arming / disarming - This option will send two short pulses (Chirps) to the output
mapped at P511E-P518E option 3 when Area "A" is armed via a radio key (Pendant) and four short
pulses to the output when Area "A" is disarmed by a radio key.
Option 5 Pendant Chirps on Stay Mode on / off - This option will send two short pulses (Chirps) to the output
mapped at P511E-P518E option 3 when Stay Mode for Area "A" is turned on with a radio key (Pendant)
and four short pulses to the output when Area "A" Stay Mode is turned off by a radio key.
Option 6 2 second output on Arming - If this option is on, the output which is assigned by P511E-P518E option
5 will turn on for 2 seconds when Area "A" is armed.
Option 7 2 second output on Disarming - If this option is on, the output which is assigned by P511E-P518E
option 5 will turn on for 2 seconds when Area "A" is disarmed.
Note: P631E is the same as above but applies to Area B Miscellaneous options
Note: P731E is the same as above but applies to Area C Miscellaneous options
Note: P831E is the same as above but applies to Area D Miscellaneous options
To Next Page
Loading...
