Crow PowerWave-64

To Next Page

To Previous Page

July 2002 PowerWave 64 V1.0 and above.

This manual relates to the Crow PowerWave 64 wireless alarm control

panel software version V1.0 and above.

Disclaimer

Crow Ltd make no warranties regarding the content of this document and

assume no responsibility for any omissions or errors contained herein.

To the best of our knowledge the information contained in this manual is

correct at the time of printing. Crow Ltd reserve the right to make changes

to the features and specifications at any time without notice in the course

of product development..

Main Page

Default Chapter1
- Default Chapter1
  - Programming Guide1
  - Table of Contents3
- Introduction5
Pw64 Lcd Keypads9
- Keypad Functions9
- Keypad Tamper9
- Addressing Individual Keypads10
- Keypad Address Assignment10
- Displaying Memory Events at a Keypad11
ACCESSING PROGRAM MODE for the FIRST TIME12
- Accessing Installer Mode from Power-Up12
- Accessing both Program Modes from Normal Run Mode12
- How to Program Your PW6412
- How to Reset the Panel Back to Factory Defaults13
- Exiting Program Modes13
User Code Programming13
- Programming User Codes13
- User Code Group Number Assignment14
- User Group Arm/Disarm Options14
- User Group Miscellaneous Options14
- User Group Radio Pendant Options15
- User Group Radio Pendant Type16
- User Group Output on Control16
- User Group Output off Control17
- User Group Time Zone Control17
- Programming the Installer Code18
- Duress Digit18
Zone Programming18
- Assigning a Group Number 1-20 to a Zone18
- Zone Group Number 1-20 Arm/Dis Arm Options19
- Zone Group Number 1-20 Alarm Type Options19
- Zone Group Number 1-20 Special Options & PA Settings20
- Zone Group Number 1-20 Wireless Type Options21
- Zone Group Number 1-20 Voice Message Options21
- Zone Group Number 1-20 Entry Delay22
- Zone Group Number 1-20 Dialling Scenario Number22
- Zone Group Number 1-20 Contact ID Alarm Event Number22
- Zone Group Number 1-20 Contact ID Tamper Alarm Event Number22
- Zone Group Number 1-20 Contact ID Reporting Account23
- Zones 61-64 Response Time23
Partition Parameters23
- Primary Area Based Alarms to Outputs23
- Secondary Area Based Alarms to Outputs24
- Area Based Arm & Stay Button Options25
- Time Zone Auto Arm/Disarm of Areas25
- Area Based Miscellaneous Keypad Options25
- Area Based Special Options26
- Area Based Time & Delay Options27
- Enabling Local PA Arm/Disarm Messages27
- Enabling Local PA Stay Mode Arm Messages28
- Area Based Dialler Reporting Options29
- Programming the Reporting Account Number29
- Assigning the Arm/Disarm Reporting Scenario29
- Assigning the Child Disarm Reporting Scenario30
Programming Radio Devices31
- Enrolling Radio Zones31
- Enrolling Radio Keys31
- Erasing a Radio Code by Transmitting the Code31
- Received Signal Strength (RSSI) for Zones32
- Received Signal Strength (RSSI) for Pendants32
General Output Program Options32
- Primary Output Options32
- Alarms to Output Options33
- Secondary Alarms to Output Options34
- Output Local PA Options35
- Assigning Time Zones to Turn Outputs On/Off35
- Assigning Time Zones to Inhibit Outputs35
Miscellaneous Panel Options35
- Hardwired Zone, RSSI & Output Board Options35
Keypad Options37
- Assigning Keypads to Areas37
- Keypads Allowed to Arm/Stay/Bypass & Control37
- Keypads with Panic/Medical & Fire Alarms Enabled37
- Various Alarms to Keypad Buzzer Programming37
- Entry & Exit Beeps to Keypad Buzzer38
- Keypad Led's off When Armed38
- Special "A" & "B" Button Options38
- Programming Delays & Timers38
Programming Real Time Clock & Time Zones40
- Setting the Real Time Clock & Daylight Saving40
- Time Zone Programming41
Miscellaneous Setup & Diagnostic Data42
- Temporary Output Disable/ Clear Output Defaults42
- Data Transfer Using EE² Board42
- Dynamic Data E.g. Keypad Address, Panel Software Version42
- Start Printing the Event Memory Buffer42
- Start Walk Test Mode43
Reset Panel to Factory Defaults43
- Reset Various Panel Functions to the Factory Default43
Command Control & Pa Options43
- Programming Codes for Arm/Disarm, Output & MIC Control43
- Recording & Playing Back Custom Voice Messages44
- Assigning Arm/Disarm/Stay & Output Voice Messages44
- Miscellaneous PA Message Assignments46
- Local & Remote Command Control Operation46
- Local Command Control of Outputs47
Dialler Programming48
- Enable Dialler & Dialling Parameters48
- Reporting Scenarios48
- Maximum Dial Attempts49
- Telephone Numbers & PH Number Prefix49
- Reporting Format for each Telephone Number50
- Telephone Number Options51
- Assigning Scenarios51
- Automatic Test Call Time52
Contact ID Code, Pa & Speech Programming52
- Account Code Numbers52
- Zone Group Alarm & Tamper Event Codes52
- Manual Fire/Panic/Medical Alarms Event Code53
- Zone Group Voice Message Assignment53
- Assigning Voice Messages to Miscellaneous Alarms53
Miscellaneous Dialler Options53
- Keypad & Speaker Listen-In Options53
- Auto-Answer Ring Count54
- Mains Failure and Zone Alarm Reporting Delays54
- Upload/Download Security Options54
4+2 Programming55
- Programming Special Characters for 4+255
Common Contact ID Codes55
Program Address Summary56
Summary of Contact ID Codes Sent by the Pw6487

Crow PowerWave-64 - Page 2

Table of Contents

Related product manuals