Crow PowerWave-64 - Page 88

88 pages

Save Page as PDF

To Previous Page

To Previous Page

Loading...

Page 88

Crow Version 1 Wireless Control Installation Guide

Table of Contents

Default Chapter1
- Default Chapter1
  - Programming Guide1
  - Table of Contents3
- Introduction5
Pw64 Lcd Keypads9
- Keypad Functions9
- Keypad Tamper9
- Addressing Individual Keypads10
- Keypad Address Assignment10
- Displaying Memory Events at a Keypad11
ACCESSING PROGRAM MODE for the FIRST TIME12
- Accessing Installer Mode from Power-Up12
- Accessing both Program Modes from Normal Run Mode12
- How to Program Your PW6412
- How to Reset the Panel Back to Factory Defaults13
- Exiting Program Modes13
User Code Programming13
- Programming User Codes13
- User Code Group Number Assignment14
- User Group Arm/Disarm Options14
- User Group Miscellaneous Options14
- User Group Radio Pendant Options15
- User Group Radio Pendant Type16
- User Group Output on Control16
- User Group Output off Control17
- User Group Time Zone Control17
- Programming the Installer Code18
- Duress Digit18
Zone Programming18
- Assigning a Group Number 1-20 to a Zone18
- Zone Group Number 1-20 Arm/Dis Arm Options19
- Zone Group Number 1-20 Alarm Type Options19
- Zone Group Number 1-20 Special Options & PA Settings20
- Zone Group Number 1-20 Wireless Type Options21
- Zone Group Number 1-20 Voice Message Options21
- Zone Group Number 1-20 Entry Delay22
- Zone Group Number 1-20 Dialling Scenario Number22
- Zone Group Number 1-20 Contact ID Alarm Event Number22
- Zone Group Number 1-20 Contact ID Tamper Alarm Event Number22
- Zone Group Number 1-20 Contact ID Reporting Account23
- Zones 61-64 Response Time23
Partition Parameters23
- Primary Area Based Alarms to Outputs23
- Secondary Area Based Alarms to Outputs24
- Area Based Arm & Stay Button Options25
- Time Zone Auto Arm/Disarm of Areas25
- Area Based Miscellaneous Keypad Options25
- Area Based Special Options26
- Area Based Time & Delay Options27
- Enabling Local PA Arm/Disarm Messages27
- Enabling Local PA Stay Mode Arm Messages28
- Area Based Dialler Reporting Options29
- Programming the Reporting Account Number29
- Assigning the Arm/Disarm Reporting Scenario29
- Assigning the Child Disarm Reporting Scenario30
Programming Radio Devices31
- Enrolling Radio Zones31
- Enrolling Radio Keys31
- Erasing a Radio Code by Transmitting the Code31
- Received Signal Strength (RSSI) for Zones32
- Received Signal Strength (RSSI) for Pendants32
General Output Program Options32
- Primary Output Options32
- Alarms to Output Options33
- Secondary Alarms to Output Options34
- Output Local PA Options35
- Assigning Time Zones to Turn Outputs On/Off35
- Assigning Time Zones to Inhibit Outputs35
Miscellaneous Panel Options35
- Hardwired Zone, RSSI & Output Board Options35
Keypad Options37
- Assigning Keypads to Areas37
- Keypads Allowed to Arm/Stay/Bypass & Control37
- Keypads with Panic/Medical & Fire Alarms Enabled37
- Various Alarms to Keypad Buzzer Programming37
- Entry & Exit Beeps to Keypad Buzzer38
- Keypad Led's off When Armed38
- Special "A" & "B" Button Options38
- Programming Delays & Timers38
Programming Real Time Clock & Time Zones40
- Setting the Real Time Clock & Daylight Saving40
- Time Zone Programming41
Miscellaneous Setup & Diagnostic Data42
- Temporary Output Disable/ Clear Output Defaults42
- Data Transfer Using EE² Board42
- Dynamic Data E.g. Keypad Address, Panel Software Version42
- Start Printing the Event Memory Buffer42
- Start Walk Test Mode43
Reset Panel to Factory Defaults43
- Reset Various Panel Functions to the Factory Default43
Command Control & Pa Options43
- Programming Codes for Arm/Disarm, Output & MIC Control43
- Recording & Playing Back Custom Voice Messages44
- Assigning Arm/Disarm/Stay & Output Voice Messages44
- Miscellaneous PA Message Assignments46
- Local & Remote Command Control Operation46
- Local Command Control of Outputs47
Dialler Programming48
- Enable Dialler & Dialling Parameters48
- Reporting Scenarios48
- Maximum Dial Attempts49
- Telephone Numbers & PH Number Prefix49
- Reporting Format for each Telephone Number50
- Telephone Number Options51
- Assigning Scenarios51
- Automatic Test Call Time52
Contact ID Code, Pa & Speech Programming52
- Account Code Numbers52
- Zone Group Alarm & Tamper Event Codes52
- Manual Fire/Panic/Medical Alarms Event Code53
- Zone Group Voice Message Assignment53
- Assigning Voice Messages to Miscellaneous Alarms53
Miscellaneous Dialler Options53
- Keypad & Speaker Listen-In Options53
- Auto-Answer Ring Count54
- Mains Failure and Zone Alarm Reporting Delays54
- Upload/Download Security Options54
4+2 Programming55
- Programming Special Characters for 4+255
Common Contact ID Codes55
Program Address Summary56
Summary of Contact ID Codes Sent by the Pw6487

Related product manuals

Preview: Crow PowerWave 8

Crow PowerWave 8

Preview: Crow PowerWave-16

Crow PowerWave-16

Crow Power Wave - 8

Preview: Crow Runner Series

Crow Runner Series

Crow Arrowhead Elite V6

Crow RUNNER 8/64