DAELIM B-BONE

7-3
ENGINE REMOVAL/INSTALLATION
● Loosen the rear cushion under bolt.
● Remove the SAI tube from the secondary air filter
assembly.
● Loosen the 10mm U nut from the engine hanger.
● Lifting the frame back side and remove the flange bolt
securing engine hanger and disassemble the frame and
engine.
REAR CUSHION UNDER BOLT
REAR CUSHION UNDER BOLT
REAR CUSHION UNDER BOLT
REAR CUSHION UNDER BOLT
REAR CUSHION UNDER BOLT
REAR CUSHION UNDER BOLT
REAR CUSHION UNDER BOLT
REAR CUSHION UNDER BOLT
REAR CUSHION UNDER BOLT
REAR CUSHION UNDER BOLT
REAR CUSHION UNDER BOLT
REAR CUSHION UNDER BOLT
REAR CUSHION UNDER BOLT
REAR CUSHION UNDER BOLT
REAR CUSHION UNDER BOLT
REAR CUSHION UNDER BOLT
REAR CUSHION UNDER BOLT
REAR CUSHION UNDER BOLT
REAR CUSHION UNDER BOLT
REAR CUSHION UNDER BOLT
REAR CUSHION UNDER BOLT
REAR CUSHION UNDER BOLT
SECONDARY
AIR FILTER
SECONDARY
AIR FILTER
SECONDARY
AIR FILTER
SECONDARY
AIR FILTER
SECONDARY
AIR FILTER
SECONDARY
AIR FILTER
SECONDARY
AIR FILTER
SECONDARY
AIR FILTER
SECONDARY
AIR FILTER
SECONDARY
AIR FILTER
SECONDARY
AIR FILTER
SECONDARY
AIR FILTER
SECONDARY
AIR FILTER
SECONDARY
AIR FILTER
SECONDARY
AIR FILTER
SECONDARY
AIR FILTER
SECONDARY
AIR FILTER
SECONDARY
AIR FILTER
SECONDARY
AIR FILTER
SECONDARY
AIR FILTER
SECONDARY
AIR FILTER
SECONDARY
AIR FILTER
REAR CUSHION
REAR CUSHION
REAR CUSHION
REAR CUSHION
REAR CUSHION
REAR CUSHION
REAR CUSHION
REAR CUSHION
REAR CUSHION
REAR CUSHION
REAR CUSHION
REAR CUSHION
REAR CUSHION
REAR CUSHION
REAR CUSHION
REAR CUSHION
REAR CUSHION
REAR CUSHION
REAR CUSHION
REAR CUSHION
REAR CUSHION
REAR CUSHION
ISA TUBE
ISA TUBE
ISA TUBE
ISA TUBE
ISA TUBE
ISA TUBE
ISA TUBE
ISA TUBE
ISA TUBE
ISA TUBE
ISA TUBE
ISA TUBE
ISA TUBE
ISA TUBE
ISA TUBE
ISA TUBE
ISA TUBE
ISA TUBE
ISA TUBE
ISA TUBE
ISA TUBE
ISA TUBE
ENGINE HANGER PLATE
ENGINE HANGER PLATE
ENGINE HANGER PLATE
ENGINE HANGER PLATE
ENGINE HANGER PLATE
ENGINE HANGER PLATE
ENGINE HANGER PLATE
ENGINE HANGER PLATE
ENGINE HANGER PLATE
ENGINE HANGER PLATE
ENGINE HANGER PLATE
ENGINE HANGER PLATE
ENGINE HANGER PLATE
ENGINE HANGER PLATE
ENGINE HANGER PLATE
ENGINE HANGER PLATE
ENGINE HANGER PLATE
ENGINE HANGER PLATE
ENGINE HANGER PLATE
ENGINE HANGER PLATE
ENGINE HANGER PLATE
ENGINE HANGER PLATE
Take precautions not to damage wiring and
cable.
Take precautions not to damage the thread part
of bolts.
Arrange the cable tube and wring in the right
positions.
!
NOTE
ENGINE INSTALLATION
● Install in the reverse order of removal.
TORQUE :
ENGINE HANGER NUT (FRONT) : 4.5
㎏
f
·
m
(REAR) : 4.5
㎏
f
·
m
● Check the following after the engine is installed.
- Engine oil
- Electric systems