Dell S4048-ON - Enabling an SNMP Agent to Notify Syslog Server Failure

provider at Level 4 VLAN 3000
%ECFM-5-ECFM_REMOTE_ALARM: Remote CCM Defect detected by MEP 3 in Domain
customer1 at Level 7 VLAN 1000
%ECFM-5-ECFM_RDI_ALARM: RDI Defect detected by MEP 3 in Domain customer1 at
Level 7 VLAN 1000
entity
Enable entity change traps
Trap SNMPv2-MIB::sysUpTime.0 = Timeticks: (1487406) 4:07:54.06,
SNMPv2-MIB::snmpTrapOID.0 = OID: SNMPv2-SMI::mib-2.47.2.0.1,
SNMPv2-SMI::enterprises.6027.3.6.1.1.2.0 = INTEGER: 4
Trap SNMPv2-MIB::sysUpTime.0 = Timeticks: (1488564) 4:08:05.64,
SNMPv2-MIB::snmpTrapOID.0 = OID: SNMPv2-SMI::mib-2.47.2.0.1,
SNMPv2-SMI::enterprises.6027.3.6.1.1.2.0 = INTEGER: 5
Trap SNMPv2-MIB::sysUpTime.0 = Timeticks: (1489064) 4:08:10.64,
SNMPv2-MIB::snmpTrapOID.0 = OID: SNMPv2-SMI::mib-2.47.2.0.1,
SNMPv2-SMI::enterprises.6027.3.6.1.1.2.0 = INTEGER: 6
Trap SNMPv2-MIB::sysUpTime.0 = Timeticks: (1489568)
4:08:15.68,SNMPv2-MIB::snmpTrapOID.0 = OID: SNMPv2-SMI::mib-2.47.2.0.1,
SNMPv2-SMI::enterprises.6027.3.6.1.1.2.0 = INTEGER: 7
<cr>
SNMP Copy Config Command Completed
%RPM0-P:CP %SNMP-4-RMON_RISING_THRESHOLD: STACKUNIT0 rising threshold alarm from
SNMP OID <oid>
%RPM0-P:CP %SNMP-4-RMON_FALLING_THRESHOLD: STACKUNIT0 falling threshold alarm from
SNMP OID <oid>
%RPM0-P:CP %SNMP-4-RMON_HC_RISING_THRESHOLD: STACKUNIT0 high-capacity rising threshold
alarm from SNMP OID <oid>
Enabling an SNMP Agent to Notify Syslog Server
Failure
You can congure a network device to send an SNMP trap if an audit processing failure occurs due to loss of connectivity with the syslog
server.
If a connectivity failure occurs on a syslog server that is congured for reliable transmission, an SNMP trap is sent and a message is
displayed on the console.
The SNMP trap is sent only when a syslog connection fails and the time-interval between the last syslog notication and current time is
greater than or equal to 5 minutes. This restriction also applies to the console message.
NOTE
: If a syslog server failure event is generated before the SNMP agent service starts, the SNMP trap is not sent.
To enable an SNMP agent to send a trap when the syslog server is not reachable, enter the following command:
CONFIGURATION MODE
snmp-server enable traps snmp syslog-unreachable
To enable an SNMP agent to send a trap when the syslog server resumes connectivity, enter the following command:
CONFIGURATION MODE
snmp-server enable traps snmp syslog-reachable
Table 90. List of Syslog Server MIBS that have read access
MIB Object OID Object Values Description
dF10SysLogTraps 1.3.6.1.4.1.6027.3.30.1.1 1 = reachable2 = unreachable Species whether the syslog
server is reachable or
unreachable.
Simple Network Management Protocol (SNMP) 869