J
Jacob LeeSep 12, 2025
What does it mean when my DITEC ENTREMATIC HA9 flashes nine times?
- MMarc FergusonSep 12, 2025
Nine flashes on your DITEC Door Opening System indicate a blocked door and constant impulse. Try toggling the impulse.
To Next PageTo Next PageWhat does it mean when my DITEC ENTREMATIC HA9 flashes nine times?
Nine flashes on your DITEC Door Opening System indicate a blocked door and constant impulse. Try toggling the impulse.
How to adjust unknown spring pretension on a DITEC ENTREMATIC HA9 Door Opening System?
To adjust the unknown spring pretension on your DITEC Door Opening System, follow these steps: 1. Turn up the potentiometer SPTE until it is possible to loosen the door stop. 2. Remove the door stop and the arm system. 3. Unplug the mains and let the spring close. 4. Unplug the motor plug. 5. Mount the drive arm from the arm system and find the pre-tension by moving back and forth. 6. Loosen the arm. 7. Connect the motor plug. 8. Connect the mains. 9. Turn the SPTE pot to 210° and wait until the spindle stops turning. 10. Mount the door stop against the closing stop block. 11. Turn down SPTE to 0º - operator is now factory set. 12. Turn to section 5.1 to adjust open stop position.
General| Motor Voltage | 24 V DC |
|---|---|
| Dimensions | Check the official documentation |
| Operating Temperature | -20°C to +55°C |
| Maximum Current | 1.5 A |
| Power Supply | 230V AC, 50/60Hz |
| Opening Speed | Adjustable |
| Closing Speed | Adjustable |
| Safety Features | Obstacle detection |
| Protection level | IP44 |
| Protection Degree | IP44 |
Mandatory safety instructions for installation to prevent injury or property damage.
Step-by-step visual guide outlining the automatic door operator installation process.
Illustrates the components and layout of a typical automatic swing door installation.
Lists and identifies all available replacement parts for the HA9 operator.
Covers intended use, safety precautions, electronic interference, and environmental requirements.
Details applicable codes, standards, and technical specifications of the HA9 operator.
Explains the operational principles of the HA9 swing door operator.
Describes the various functions and operational modes of the HA9 control unit.
Details the functions and capabilities of the EXU-SI standard extension unit.
Outlines the features and functionalities of the EXU-SA optional extension unit.
Covers essential steps and considerations before commencing the installation process.
Provides tips on door edge safety, security, wiring, and entrapment prevention.
Addresses environmental factors, ADA requirements, and necessary tools for installation.
Explains how to determine the operator type (Push/Pull) and door handing (Left/Right).
Steps for disassembling and preparing the header box before mounting.
Detailed instructions for mounting the header box for push-type door installations.
Instructions for mounting the header box for pull-type door installations.
Guidance for installing the header for double egress doors with both push and pull operators.
Steps for safely connecting the incoming mains power to the operator unit.
Procedure for reconfiguring the operator from push to pull requirements.
Instructions for correctly reinstalling the motor/gearbox assembly onto the mounting studs.
Identifies main components of the push arm and standard configuration.
Details an alternative push arm setup for installations with clearance issues.
Step-by-step guide for installing the push arm onto the operator and door.
Describes the setup and mounting for the pull arm in pull-type applications.
Guides on marking closed and open positions for accurate pull arm installation.
Instructions for fitting the pull track and making necessary adjustments for optimal operation.
Final steps for attaching the pull arm to the roller shaft and ensuring proper alignment.
Details the main HA9 control board, arm system selection, and configuration settings.
Instructions for installing EXU-SI and EXU-SA extension units onto the HA9 control unit.
Explains the functions, inputs, and connections for the EXU-SI standard extension unit.
Describes the functions, inputs, and sensor connections for the EXU-SA optional extension unit.
Procedure for adjusting the door's back check and latching points for optimal performance.
How to adjust the micro switch for the lock kick function for proper closing and latching.
Instructions for connecting and configuring the sync cable for synchronized double door operation.
Defines parameter settings for MASTER and SLAVE operators in double door configurations.
Automatic learning process to set back-check, latch-check, and open positions.
How to use the Learn button for delayed or direct opening during auto-learn.
Specific procedures for learning double door systems using the Learn button.
Advanced method for setting back-check and latch-check parameters.
Procedure to reset back-check, latch-check, and open position to factory default settings.
Covers adjustments for hold open time, opening/closing speed, and activation units.
Guide to reducing or increasing the spring pre-tension for proper door closing force.
Wiring diagrams and instructions for connecting activation sensors and accessories.
Steps for adjusting operator parameters using the Learn button and group selection.
Configuration and recommended settings for the Overhead Presence Detection sensor.
How to configure the lock kick function for enhanced security during closing.
Setting up the lock unlock function based on door position.
Information on integrating safety sensors, knowing act devices, and jamb switches.
Instructions for installing the header cover after all adjustments are completed.
Guidance on properly applying safety and instruction decals to the door.
Visual examples showing the correct placement of safety stickers on doors.
Lists common problems like door not opening/closing and their solutions.
Explains error codes indicated by the LED flash frequency and their corresponding remedies.
Guidelines for regular inspections and scheduled maintenance by qualified technicians.
Contact information for Entrematic Canada and USA, and technical service department.
Lists the codes and standards the HA9 operator complies with.
