DoAll DS-320SA - Page 3

DS-320SA
Instruction Manual - 3 -
www.doallsaws.com
9.8.2 ADJUSTMENT OF THE DOWN WORKING POSITION ............................................................ 38
9.9 VICE ADJUSTMENT - HOW TO CLAMP THE MATERIAL WELL ....................................................... 39
9.10 GUIDE POSITION ADJUSTMENT ...................................................................................................... 39
9.11 LUBRICATION OF THE SAW - BAND ................................................................................................ 40
9.12 HOW TO SET THE ADJUSTABLE END STOP ................................................................................. 40
9.13 HANDLING THE MATERIAL ............................................................................................................... 40
10. CUTTING - SEMIAUTOMATIC CYCLE ..................................................................................................... 41
10.1 BASIC CONDITIONS FOR CUTTING ................................................................................................. 41
10.2 HYDRAULIC UNIT – TURNING ON .................................................................................................... 41
10.3 CUTTING ............................................................................................................................................. 41
10.4 ERROR MESSAGES ........................................................................................................................... 41
10.5 15 RULES FOR OPTIMAL CUT .......................................................................................................... 44
11. INFORMATION ABOUT THE BLADE ....................................................................................................... 45
11.1 TENSIONING OF THE SAW-BAND .................................................................................................... 45
11.2 BAND REPLACEMENT ....................................................................................................................... 46
11.3 GUIDES OF THE BLADE .................................................................................................................... 47
11.4 HOW TO REPLACE THE CLEANING BRUSH ................................................................................... 48
11.4.1 HOW TO CHANGE THE BRUSH .......................................................................................... 48
12. HOW TO CHOOSE THE RIGHT SAW-BLADE......................................................................................... 49
12.1 SAW-BLADE TEETH ........................................................................................................................... 49
12.2 HOW TO CHOOSE THE RIGHT TEETH FOR CUTTING ................................................................... 50
12.3 RUN IN OF SAW-BLADE - WHEN HAVING A NEW SAW-BLADE .................................................... 50
12.4 HOW TO CLAMP MATERIAL .............................................................................................................. 51
12.5 SPEED OF ARM MOVEMENT WHEN CUTTING ............................................................................... 51
12.5.1 EXTRA ACCESSORIES ........................................................................................................ 52
12.6 MINI-LUBE ........................................................................................................................................... 54
5.5.1 SETTING AND ADJUSTMENT ...................................................................................................... 54
12.6.1 CONTROL .............................................................................................................................. 54
12.7 HYDRAULICAL UPPER VICE .............................................................................................................. 55
12.7.1 UPPER THRUST SETTING ................................................................................................... 55
12.7.2 CONTROLLING OF UPPER THRUST ................................................................................... 56
12.7.3 ASSEMBLY / DISMANTLE OF UPPER THRUST .................................................................. 56
12.8 LIGHT ................................................................................................................................................... 56
12.9 ROLLER TABLE .................................................................................................................................. 57
13. MAINTENANCE ......................................................................................................................................... 61
13.1 LUBRICATION CHECKING ................................................................................................................. 62
13.2 RECOMMENDED FILLINGS- INTERVALS FOR CHANGING FILLINGS .......................................... 63
13.3 CHANGE OF HYDRAULIC OIL ........................................................................................................... 63
13.4 FILLING THE TANK WITH OIL ............................................................................................................ 64
13.5 FILLING AND CHANGING PUMP COOLANT..................................................................................... 64
13.5.1 STIRRING THE COOLANT .................................................................................................... 65
13.5.2 PROPORTION OF OIL AND WATER MIXTURE .................................................................. 65
13.5.3 LIFETIME OF THE COOLANT ............................................................................................... 65
13.6 CHANGE OF GEAR OIL ...................................................................................................................... 65
13.6.1 TECHNICAL MAINTENANCE OF GEARBOXES .................................................................. 65
14. SERVICE INSTRUCTIONS ........................................................................................................................ 66
14.1 ADJUSTMENT OF BAND GUIDES ..................................................................................................... 66
14.2 ADJUSTMENT OF CLEARANCE BETWEEN THE SAW-BAND AND CARBIDE PADS.................... 67
14.3 ADJUSTMENT OF THE TENSIONING PULLEY ................................................................................ 68
14.4 ADJUSTING THE HYDRAULIC PUMP PRESSURES: ....................................................................... 69
14.5 SETTING PRESSURES ...................................................................................................................... 69
14.6 REPLACING THE COUPLING BETWEEN THE ELECTRIC MOTOR AND HYDRAULIC PUMP ...... 70
14.7 HOW TO SOLVE PROBLEMS-MACHINE .......................................................................................... 72
15. CLOSING ................................................................................................................................................... 73