DoAll DS-320SA - 12.2 HOW TO CHOOSE THE RIGHT TEETH FOR CUTTING; 12.3 RUN IN OF SAW-BLADE - WHEN HAVING A NEW SAW-BLADE

DS-320SA
Instruction Manual - 50 -
www.doallsaws.com
12.2 HOW TO CHOOSE THE RIGHT TEETH FOR CUTTING
The table for choosing saw-blade is attached to the machine.
CONSTANT VARIABLE CONSTANT VARIABLE
A teeth A teeth A teeth A teeth
-0,25 22 -0,8 6/10 -0,6 14 - 0,6 10/14
0,25-0,4 18 0,8-1,6 5/8 0,6-1,6 10 0,6 – 1,6 8/12
0,4-0,8 14 1,6-3,2 4/6 1-2 8 1 – 2 6/10
0,8-1,2 10 3,2-6,5 3/4 1,4-2,8 6** 1,4 – 2,8 5/8
1,2-2 8 6,5-8 2/3 1,6-3,2 4** 1,6 – 3,2 5/6
2-3,2 6 8-16 1,4/2
2-4,7
3** 2 – 4,7
4/6 * **
3,2-4,8 4 16-25 1/1,3
3,2-7
2 3,2 – 7
3/4 * **
4,8-8 3 > 25 0,75/1,25
5-14
1,25 5 – 14
2/3
8-16 2
6-18
0,75 6 – 18
1,5/2
16-32 1,25
8-24
8 – 24
1,1/1,6
> 32 0,75
>20
> 20
0,75/1,25
tab. 12-1
T/D 0,8 1,6 2,4 3,2 4 4,8 6 8 12 20
0,08 14 10/14 10/14 10/14 10/14 8/12 8/12 8/12 8/12 5/8
0,12 14 10/14 10/14 8/12 8/12 8/12 8/12 6/10 6/10 5/8
0,16 10/14 10/14 8/12 8/12 8/12 6/10 6/10 5/8 5/8 4/6 S
0,2 10/14 10/14 8/12 8/12 6/10 6/10 5/8 4/6 S 4/6 S 4/6 S
0,24 10/14 8/12 8/12 6/10 6/10 5/8 5/8 4/6 S 4/6 S 4/6 S
0,32 10/14 8/12 8/12 6/10 5/8 5/8 4/6 4/6 4/6 4/6
0,4 8/12 6/10 5/8 4/6 4/6 4/6 4/6 4/6 4/5
0,5 8/12 6/10 4/6 4/6 4/6 4/6 4/6 4/6 4/5
0,6 8/12 6/10 4/6 4/6 4/6 4/6 4/5 4/5 4/5
0,8 4/6 4/6 4/6 4/6 4/6 4/5 4/5 3/4
1,2 4/6 4/6 4/5 4/5 4/5 4/5 2/3
2 4/5 3/4 2/3 2/3
3 3/4 2/3 2/3
> 4 2/3 1,5/2
tab. 12-2
12.3 RUN IN OF SAW-BLADE - WHEN HAVING A NEW SAW-BLADE
Run in is necessary for achieving max. saw-blade life cycle. By running in
you prevent breaking microfragments of teeth, that damage other teeth and
increase stress to the saw-blade.
Let saw-blade run on no-load for about 30 seconds with the coolant pump
working ( due to right lubrication of saw-blade). Run in do if possible with easy
machined materials by min. speed of arm when cutting. After about 30
minutes increase the speed of feed continuously.