Model 5601MSC
Model 5601MSC Master SPG/Master Clock System
TABLE OF CONTENTS Revision 2.2 Page - iii
4.1.1. Front Panel Buttons .......................................................................................................... 69
4.1.2. The Status Screens .......................................................................................................... 70
4.1.3. Panel Lock Function ......................................................................................................... 76
4.1.4. Front Panel LCD Displays ................................................................................................ 76
4.2. FRONT PANEL MENU SYSTEM ................................................................................................ 77
4.2.1. Menu Reference Guide .................................................................................................... 79
4.3. CONFIGURING THE INPUT REFERENCES ............................................................................... 90
4.3.1. Selecting the Frequency Reference ................................................................................. 90
4.3.2. Configuring the Genlock Capture Range .......................................................................... 91
4.3.3. Selecting the Frequency Reference Lock Type ................................................................ 91
4.3.4. Selecting the Time Reference .......................................................................................... 92
4.3.5. Setting the VITC Reader Line ........................................................................................... 93
4.3.6. Configuring the VITC and LTC Time Reference Date Format ........................................... 93
4.3.7. Selecting the IRIG Input Mode.......................................................................................... 93
4.3.8. Selecting the SNTP IP Enable .......................................................................................... 94
4.3.9. Selecting the SNTP IP Address ........................................................................................ 94
4.3.10. Selecting the Time Reference Lock Type ......................................................................... 95
4.3.11. Setting the Daily Jam Time for the Time Reference .......................................................... 95
4.3.12. Synchronizing the System Oscillator or System Time to the Reference Immediately ........ 96
4.4. CONFIGURING THE OUTPUTS ................................................................................................. 97
4.4.1. Configuring the LTC Outputs ............................................................................................ 98
4.4.1.1. Selecting Normal or Powered LTC 1 Output (LTC1 XLR Output Only) ................... 98
4.4.1.2. Setting the LTC Output Frame Rate and IRIG ........................................................ 99
4.4.1.3. Selecting when the LTC Time is Synchronized to the System Time ..................... 100
4.4.1.4. Synchronizing the LTC Output Time to System Time Immediately ....................... 100
4.4.1.5. Synchronizing All the LTC and VITC Outputs to System Time Immediately.......... 100
4.4.1.6. Setting the LTC Frame Offset ............................................................................... 100
4.4.1.7. Selecting the LTC Time Zone Offset..................................................................... 101
4.4.1.8. Enabling Daylight Saving Time for the LTC Output ............................................... 101
4.4.1.9. Setting the LTC/IRIG Output Level ....................................................................... 101
4.4.1.10. Enabling LTC Polarity Correction ......................................................................... 102
4.4.1.11. Enabling the LTC Output Color Frame Bit ............................................................ 102
4.4.1.12. Selecting the IRIG Output Format ........................................................................ 102
4.4.1.13. Setting a Time Offset to the IRIG Output .............................................................. 102
4.4.2. Configuring the Sync, 10MHZ and Wordclock Outputs ................................................... 102
4.4.2.1. Selecting the Standard of the Sync Outputs ......................................................... 103
4.4.2.2. Configuring the VITC Generator for the Color Black Outputs ................................ 103
4.4.2.3. Setting the Phase of the Sync Outputs ................................................................. 109
4.4.3. Configuring the SDI Video Test Generator Outputs (SDTG, HDTG, 3GTG options) ....... 111
4.4.3.1. Selecting the SDI Test Generator Test Pattern ..................................................... 111
4.4.3.2. Selecting the Interface Type of the SDI Video Test Generator ............................. 111
4.4.3.3. Selecting the Image Format of the SDI Video Test Generator .............................. 112
4.4.3.4. Selecting Sampling Structure of the SDI Video Test Generator ............................ 112
4.4.3.5. Setting the Phase of the SDI Video Test Generator .............................................. 113
4.4.3.6. Configuring the SDI Test Generator Embedded Audio ......................................... 113
4.4.3.7. Configuring the On-Screen Message for the SDI Test Generator Outputs ............ 115
4.4.3.8. Configuring the SDI Test Generator Output Drive................................................. 118
4.4.3.9. Setting the SDI Test Generator Syncro Mode ....................................................... 118
4.4.4. Configuring the Analog Video Test Generator Outputs (SDTG, HDTG, 3GTG Options) . 118
To Next Page
Loading...
