DAD 143.x User Manual Profinet Rev.1.1.1 March 2023 Page 3 of 95
8 Setup via PC / PLC - Command Overview - .......................................................................................................... 31
8.1 Special Commands of DAD143.x Overview .................................................................................................................. 34
8.1.1 AT Auto Transmit (for service port RS 232 connection, only) ............................................................................................ 34
8.1.2 AT Auto Transmit (for PLC connection) ..................................................................................................................................... 34
8.1.3 LE Last Error List (only for RS 232 connection) ...................................................................................................................... 35
9 Setup via PC / PLC - Command Descriptions ...................................................................................................... 36
9.1 System Diagnosis Commands ID, IH, IV, IS, SR, RS .................................................................................................... 36
9.1.1 ID Get Device Identity ..................................................................................................................................................................... 36
9.1.2 IV Get Firmware Version ................................................................................................................................................................ 36
9.1.3 IS Get Device Status ........................................................................................................................................................................ 36
9.1.4 SR Reset DAD143.x Firmware ...................................................................................................................................................... 37
9.1.5 RS Read Serial Number .................................................................................................................................................................. 37
9.2 Calibration Commands CS, SU, RU, FT .............. 37
9.2.1 CE Read TAC* Counter / Open Calibration Sequence ............................................................................................................. 37
9.2.2 ....................................................................................................................................... 38
9.2.3 CI Set Minimum Output Value ................................................................................................................................................ 38
9.2.4 MR Set Multi-range / Multi-interval ..................................................................................................................................... 38
9.2.5 DS Set Display Step Size ........................................................................................................................................................... 39
9.2.6 DP Set Decimal Point Position .................................................................................................................................................. 39
9.2.7 CZ Set Calibration Zero Point .................................................................................................................................................... 39
9.2.8 CG Set Calibration Gain (Span) ................................................................................................................................................ 39
9.2.9 CV Calibrate Value ...................................................................................................................................................................... 39
9.2.10 AV Show Actual Internal mV/V Value ................................................................................................................................... 40
9.2.11 ZT Zero Tracking ........................................................................................................................................................................... 40
9.2.12 FD Reset to Factory Default Settings ...................................................................................................................................... 40
9.2.13 ZR Zero Range ................................................................................................................................................................................. 40
9.2.14 ZI Initial Zero ON / OFF ............................................................................................................................................................... 40
9.2.15 TM Tare mode ................................................................................................................................................................................ 41
9.2.16 TN Set / Clear Non-Volatile Tare ............................................................................................................................................. 41
9.2.17 ZN Set / Clear Non-Volatile Zero ............................................................................................................................................ 41
9.2.18 ZM Zero Mode................................................................................................................................................................................ 41
9.2.19 AZ Absolute zero point calibration (eCal) ............................................................................................................................. 41
9.2.20 AG Absolute gain calibration (eCal) ........................................................................................................................................ 42
9.2.21 CS Save the Calibration Data ...................................................................................................................................................... 42
9.2.22 SU Save User Setup in EEPROM ............................................................................................................................................. 42
9.2.23 RU Restore User Setup to DAD143.x ...................................................................................................................................... 42
9.2.24 FT Firmware Type ........................................................................................................................................................................ 42
9.3 Motion Detection Commands NR, NT ............................................................................................................................ 43
9.3.1 - .............................................................................................................................................................. 43
9.3.2 - ............................................................................................................................................... 43
9.4 Filter Setting Commands FM, FL, PF, UR ...................................................................................................................... 43
9.4.1 FM Filter Mode ................................................................................................................................................................................... 43
9.4.2 FL Filter Settings ........................................................................................................................................................................... 44
9.4.3 PF Pre-filter .................................................................................................................................................................................... 46
9.4.4 UR Update Rate and Averaging ............................................................................................................................................... 46
9.5 Taring and Zeroing Commands SZ, RZ, ZN, ST, RT, SP, TN, RW, TI ....................................................................... 46
9.5.1 SZ Set System Zero .......................................................................................................................................................................... 46
9.5.2 RZ Reset Zero ................................................................................................................................................................................ 46
9.5.3 ST Set Tare...................................................................................................................................................................................... 47
9.5.4 RT Reset Tare ................................................................................................................................................................................. 47
9.5.5 SP Set Preset Tare .......................................................................................................................................................................... 47
9.5.6 TW Window for Automatic Taring ........................................................................................................................................ 47
9.5.7 TI Averaging Time for Automatic Taring ................................................................................................................................ 48
9.6 Output Commands GG, GN, ON, GT, GS, GW, GA, GH, GM, RM, GO, GV .............................................................. 48
9.6.1 GG Get Gross Value .......................................................................................................................................................................... 48
9.6.2 GN Get Net Value .......................................................................................................................................................................... 48
9.6.3 GT Get Tare Value ....................................................................................................................................................................... 48
To Next Page
Loading...
Need help?
General
