Flowserve Limitorque QX User Manual

Limitorque QX Electronic Actuator FCD LMENIM3306-06 – 07/14
38
7. When configuration is complete, answer “YES” to “EXIT SETUP?” Alternatively, the “SETUP” mode may be
terminated at any time by moving the red selector knob from “STOP” to “LOCAL” or “REMOTE.” All the changes
made so far will automatically be saved.
NOTE: Once you exit this mode and enter either the “VIEW SETTINGS?” mode or “VIEW DIAGNOSTICS?” mode, the
password will need to be entered again to gain access to the “CHANGE SETTINGS?” mode in order to make further
changes.
Figure 4.1 – Entering the setup mode
Entering the setup mode
Language selection
Change or view settings
See Figure 4.3
See Figure 3.15
See Figure 5.2
SETUP
IN ENGLISH?
XX% OPEN
STATUS OK
SETUP?
SETUP
IN MANDARIN?
SETUP
IN ESPANOL?
SETUP
IN GERMAN?
SETUP
IN RUSSIAN?
SETUP
IN FRANCAS?
To place actuator in the
“SETUP” mode, put red
selector knob in “STOP.”
Operate black selector knob
“YES,” “NO,” “YES.” The
message “SETUP?” will be
displayed for 10 seconds.
CHANGE
SETTINGS
VIEW
SETTINGS?
VIEW
DIAGNOSTICS?
EXIT
SETUP?
SETUP?
YES
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
YES
Toggle “NO” to select between English and other languages for setup dialogue.
YES
YES
YES
YES
SETUP
IN ITALIAN?
NO
SETUP
IN PORTUGUESE?
NO
SETUP
IN KATAKANA?
NO
SETUP
IN INDONESIAN?
NO
SETUP
IN TURKISH?
NO
Figure 4.2 – Main menu selections
CLOSE TORQUE
OPEN TORQUE
STATUS
PROP BAND
FAIL POSITION
DEADBAND
POLARITY
DELAY
HIGH SIGNAL
LOW SIGNAL
STANDARD REMOTE CONTROL
NEGATIVE SWITCHING
NOTE 1:
These are optional
displays that will
not appear unless
pur
chased.
STATUS
ANALOG SCALE
MODE
PROP/DEADBAND
STATUS
PROTOCOL/BAUD RATE
NETWORK ADDRESS
ANALOG SCALE
ESD ACTION
PROP/DEADBAND
OFFSET
RELAY
FUNCTION
CONTACT
OPEN/CLOSE
STATUS
POSITION
ON PULSE TIME
OFF PULSE TIME
SETUP
ACTUATOR
SETUP IN
ENGLISH ?
CHANGE
SETTINGS
ENTE R
PASSWORD
VIEW
SETTINGS
VIEW
DIAGNOSTICS
EXIT
SETUP?
CHANGE/VIEW TORQUE TIMER
CHANGE/VIEW OPERATING TIME
CHANGE/VIEW VALVE SETTINGS
CHANGE/VIEW TORQUE SETUP
CHANGE POSITION SETUP
CHANGE/VIEW MODUTRONIC
1
CHANGE/VIEW DDC
CHANGE/VIEW FF
1
1
CHANGE/VIEW STATUS & ALARM
CHANGE/VIEW 2-SPEED TIMERS
CHANGE/VIEW ANALOG OUT
CHANGE/VIEW REMOTE MODE
CHANGE/VIEW LOCAL CONTROL
CHANGE/VIEW ESD OVERRIDES
CHANGE/VIEW INPUTS
CHANGE/VIEW MONITOR RELAY
CHANGE DIAGNOSTIC RESET
CHANGE TAG NUMBER
CHANGE LCD CONTRAST
CHANGE PASSWORD
CHANGE/VIEW MOTOR THERMOSTAT
CHANGE/VIEW VALVE JAM SETTINGS
CHANGE/VIEW VALVE DATA
CHANGE/VIEW PORT
VIEW HARDWARE STATUS
VIEW MOTOR STATUS
VIEW ERROR CODE
VIEW POWER SUPPLY
VIEW IDENTIFICATION
VIEW TORQUE PROFILE
VIEW OPERATION LOG
CLOSE DIRECTION
CLOSE SEATING
OPEN SEATING
SETUP IN ...
MANDARIN?
ESPANOL?
GERMAN?
RUSSIAN?
FRANCAIS?
YES
NO
YES
YES
YES
NO
YES
NO
YES
1
CHANGE/VIEW UNIT DATA
CHANGE/VIEW BACKUP POWER
VALVE S/N
VALVE MODEL #
VALVE TYPE
CUSTOM CONTROL
1
CHANGE/VIEW PB
CHANGE/VIEW DN
STATUS
ANALOG SCALE
MODE
PROP/DEADBAND
STATUS
ANALOG SCALE
MODE
PROP/DEADBAND
ITALIAN?
PORTUGESE?
INDONESIAN?
KATAKANA?
TURKISH?
NO

Flowserve Limitorque QX Specifications

General

Brand	Flowserve
Model	Limitorque QX
Category	Controller
Language	English