5520A
Operators Manual
4
PREV MENU key, 3-5
pulse capture, verifying (SC600), 8-31
pulse response calibration, SC300
option, 8-72, 8-73
pulse response calibration, SC600 option, 8-19
query commands, 5-27
queue, error, 5-45
queue, output, 5-44
rack mount kit, 9-4
RANGE remote command, SC600 option, 8-37
RANGE? remote command, 6-35
RANGELCK remote command, 6-36
RANGELCK? remote command, 6-36
rear panel features, 3-3
REFCLOCK remote command, 6-37
REFCLOCK? remote command, 6-37
REFCLOCK_D remote command, 6-37
REFCLOCK_D? remote command, 6-37
REFOUT? remote command, 6-38
REFPHASE remote command, 6-38
REFPHASE? remote command, 6-38
REFPHASE_D remote command, 6-39
REFPHASE_D? remote command, 6-39
registers
ESE (event status enable register), 5-40
ESR (event status register), 5-40
ISCE0 and 1 (instrument status change enable
registers), 5-42
ISCR0 and 1 (instrument status change
registers), 5-42
ISR (instrument status register), 5-42
SRE (service request enable), 5-39
remote commands
SC300 oscilloscope commands, detailed, 8-83
SC600 oscilloscope calibration, 8-34
remote commands (Chapter 6), 6-3
remote example, verifying a meter, 5-47
remote operation (Chapter 5), 5-4
REMOTE remote command, 6-39
remote state, 5-22
remote with lockout state, 5-22
remote/local operation, changing between, 5-22
RESET key, 3-6
resetting parameters, SC600 option, 8-16
resistance
(compensation off) connections, 4-14
(four-wire) connections, 4-13
(two-wire) connections, 4-13
setting the output, 4-37
response message syntax, 5-36
RPT_STR remote command, 6-40
RPT_STR? remote command, 6-40
RS-232
interface overview, 5-23
interface, using for remote control, 5-10
modem cables, 9-4
null-modem cables, 9-4
remote control connections, 5-7
RTD connections, 4-17
RTD_TYPE remote command, 6-41
RTD_TYPE? remote command, 6-41
RTD_TYPE_D remote command, 6-41
RTD_TYPE_D? remote command, 6-42
SC300 option
verification tables, 8-86
SC300 oscilloscope calibration option, 8-59
SC600 option
verification tables, 8-41
SC600 oscilloscope calibration
introduction, 8-5
SCOPE key, 3-5
SCOPE OUT BNC connector, 3-8
SCOPE remote command, for SC300, 8-84
SCOPE remote command, SC600 option, 8-35
SCOPE TRIG BNC connector, 3-8
SCOPE? remote command, for SC300, 8-85
SCOPE? remote command, SC600 option, 8-36
sequential commands, 5-30
SERIAL 1 FROM HOST connector, 3-10
SERIAL 2 TO UUT connector, 3-10
serial poll
status byte, 5-37
service request (SRQ line), 5-39
service request enable register (SRE), 5-39
SETUP key, 3-6
SETUP softkey menu tree, 3-12
SHIFT key, 3-8
sine wave, 4-47
softkey menu trees, 3-3
softkeys, 3-5
SP_SET, 6-42
SP_SET? remote command, 6-43
space or tab characters, 5-34
specifications
ac current (non-sine wave), 1-32
ac current (sine wave) extended band
width, 1-31
ac current, square wave characteristics
(typical), 1-34
ac current, triangle wave characteristics
(typical), 1-34
ac power (45 Hz to 65 Hz) summary, 1-22
ac voltage
dc offset, 1-30
ac voltage (non-sine wave), 1-29
ac voltage (sine wave) extended
bandwidth, 1-28
ac voltage, square wave characteristics, 1-31
ac voltage, triangle wave characteristics
(typical), 1-31
capacitance, 1-19
dc current, 1-13
To Next Page
Loading...
