FOR-A MFR Series - User Manual

Other manuals for FOR-A MFR Series

Operation Manuals59 pages

Quick Start Guide2 pages

Questions and Answers

J
James SalazarAug 18, 2025
How to fix FOR-A MFR when there is no image output?
- T
  Tammy RiceAug 18, 2025
  If you're experiencing no image output on your FOR-A Switch, first ensure that video signals are being input to the video input connectors. Check that the cables are correctly connected for the signal inputs. Finally, verify that the crosspoint is set properly.
E
Emily KelleyAug 21, 2025
What to do if there is no image output from FOR-A Network Router?
- C
  Chelsea DunnAug 21, 2025
  If you're experiencing no image output on your FOR-A Network Router, first ensure that video signals are being input to the video input connectors. Next, verify that the cables are properly connected for these signal inputs. Finally, check that the crosspoint settings are correct.
J
John HamiltonAug 23, 2025
Why I am unable to control FOR-A Network Router using the remote control panel?
- G
  greenfrankAug 23, 2025
  If you can't control your FOR-A Network Router using the remote control panel, start by ensuring the LAN cable is properly connected. Then, check the RU Info page in the Web-based Control to see if it indicates 'NG' for any items. If 'NG' is indicated for Voltage, contact your FOR-A agent. For other items, consult the Web-based Control Operation Manual for details.
M
Mark HillAug 26, 2025
What to do if the secondary CPU is active on FOR-A Network Router?
- H
  hwilliamsAug 26, 2025
  If the secondary CPU is active on your FOR-A Network Router, first ensure that both MFR-LAN (CPU1) and MFR-LAN (CPU2) are correctly connected to the network by checking the cable and Ethernet hub connections. If the network connections are properly made, turn the unit power OFF, and then ON again. If the secondary CPU is still active after restarting, consult your FOR-A reseller.
J
Jennifer RomeroAug 28, 2025
Why is there no image output from my FOR-A MFR Switch?
- B
  Brian RoblesAug 28, 2025
  If there's no image output from your FOR-A Switch, first ensure video signals are being input to the video input connectors. Next, verify that the cables are correctly connected for these signal inputs. Finally, confirm that the crosspoint is properly set. If the video input connectors don't have input video signals, input them. If the cables aren't properly connected, connect them correctly. If the crosspoint isn't set properly, set it correctly.
M
Miranda HartAug 30, 2025
What to do if I'm unable to control FOR-A Switch using the remote control panel?
- R
  robertcollinsAug 30, 2025
  If you are unable to control your FOR-A Switch using the remote control panel, check if the LAN cable is properly connected. If it is not, properly connect the LAN cable. Also, check the RU Info page in the Web-based Control to see if it indicates 'NG'. If it does, check the item indicated as NG. However, if the Voltage is indicated as NG, contact your FOR-A agent.
L
Lauren YoungSep 1, 2025
How to fix the issue when the secondary CPU is active on FOR-A MFR?
- A
  Andrew JohnstonSep 1, 2025
  If the secondary CPU is active on your FOR-A Switch, make sure both MFR-LAN (CPU1) and MFR-LAN (CPU2) are correctly connected to the network by checking the cable and Ethernet hub connections. If network connections are properly made, turn the unit power OFF then ON again. If the secondary CPU is still active after restarting, consult your FOR-A reseller.
K
Karen MoranSep 3, 2025
How to fix FOR-A Switch when I cannot control it via Web-Based Control?
- P
  pharperSep 4, 2025
  If you're having trouble controlling your FOR-A Switch via web, first use commands like 'ping' to check the connection. If pings fail, verify that the PC's IP address doesn't conflict with another unit, MASK is set to 255.255.255.0, and Gateway is either None or 192.168.1.1. Also, try turning off all security software like firewalls and reconnecting. Restarting your browser may also help. Make sure that the login dialog box appears. Finally, check your browser and security settings to ensure that Active X controls and active scripting are enabled.
D
Dana LeachSep 6, 2025
What to do if an internal error message appears on FOR-A Switch (Error code: 1001)?
- D
  Dorothy GonzalezSep 6, 2025
  If you see the message “An internal error has occurred. The server will restart.” with error code 1001 on your FOR-A Switch, click OK and then restart your web browser.
F
Frank BurkeSep 8, 2025
Why channel names are not displayed on FOR-A Switch for the HVS or MV series unit?
- D
  Dale HernandezSep 8, 2025
  If channel names aren't showing up on your FOR-A Switch for the HVS or MV series unit, it might be because of the character encoding. To display names correctly, ensure that the names are set under Name (ASCII).