Fuji Electric Frenic-Mini - Page 105

6.2 Selecting Wires and Crimp Terminals
6-5
Chap. 6 SELECTING PERIPHERAL EQUIPMENT
Table 6.2 Cont. (kW, mm
2
ratings) (for DC reactor, braking resistor, control circuits, and inverter grounding)
Recommended wire size (mm
2
) at 50°C (122°F) or below
DC reactor
[P1, P(+)]
Braking resistor
[P(+), DB]
Control circuit
Inverter
grounding z[G]
Allowable
temp.*1
Allowable
temp.*1
Allowable
temp.*1
Allowable
temp.*1
Power
supply
voltage
Applicable
motor
rating
(kW)
Inverter type
60°C75°C90°C
Current
(A)
60°C75°C90°C
Current
(A)
60°C 75°C 90°C 60°C 75°C90°C
0.1 FRN0001C2S-2 0.7
0.2 FRN0002C2S-2 1.1
- - - -
0.4 FRN0004C2S-2 2.0 1.2
0.75 FRN0006C2S-2 3.7 1.6
1.5 FRN0010C2S-2 7.0 3.6
2.2 FRN0012C2S-2
2.0
(2.5)
10.2 3.5
3.7 FRN0020C2S-2
3.5
(4.0)
2.0
(2.5)
17.2 4.1
2.0
(2.5)
2.0
(2.5)
2.0
(2.5)
5.5 FRN0025C2S-2
5.5
(6)
3.5
(4)
2.0
(2.5)
25.9 6.4
3.5
(4)
3.5
(4)
3.5
(4)
7.5 FRN0033C2S-2
14
(16)
5.5
(6)
3.5
(4)
35.3 6.1
11 FRN0047C2S-2
22
(25)
8
(10)
5.5
(6)
51.7 9.1
5.5
(6)
5.5
(6)
5.5
(6)
Three-
phase
200 V
15 FRN0060C2S-2
38
(50)
14
(16)
14
(16)
70.6
2.0
(2.5)
2.0
(2.5)
2.0
(2.5)
11.0
0.5 0.5 0.5
8
(10)
8
(10)
8
(10)
0.4 FRN0002C2-4 1.0 0.8
0.75 FRN0004C2-4 1.9 1.1
1.5 FRN0005C2-4 3.6 1.8
2.2 FRN0007C2-4 5.3 1.8
3.7/4.0 FRN0011C2-4 9.0 2.1
5.5 FRN0013C2-4
2.0
(2.5)
13.0 3.2
2.0
(2.5)
2.0
(2.5)
2.0
(2.5)
7.5 FRN0018C2-4
3.5
(4)
2.0
(2.5)
17.7 3.1
11 FRN0024C2-4
5.5
(6)
3.5
(4)
2.0
(2.5)
25.9 4.5
Three-
phase
400 V
15 FRN0030C2-4
14
(16)
5.5
(6)
3.5
(4)
35.3
2.0
(2.5)
2.0
(2.5)
2.0
(2.5)
5.7
0.5 0.5 0.5
3.5
(4)
3.5
(4)
3.5
(4)
0.1 FRN0001C2-7 1.1
0.2 FRN0002C2-7 2.0
- - - -
0.4 FRN0004C2-7 3.5 0.82
0.75 FRN0006C2-7 6.4 1.4
1.5 FRN0010C2-7
2.0
(2.5)
11.7 1.4
2.0
(2.5)
Single-
phase
200 V
2.2 FRN0012C2-7
3.5
(4.0)
2.0
(2.5)
2.0
(2.5)
17.5
2.0
(2.5)
2.0
(2.5)
2.0
(2.5)
1.7
0.5 0.5 0.5
3.5
(4.0)
2.0
(2.5)
2.0
(2.5)
0.1 FRN0001C2S-6U
0.2 FRN0002C2S-6U
- - - -
0.4 FRN0003C2S-6U 0.82
Single-
phase
100 V
0.75 FRN0005C2S-6U
- - - -
2.0
(2.5)
2.0
(2.5)
2.0
(2.5)
1.4
0.5 0.5 0.5
2.0
(2.5)
2.0
(2.5)
2.0
(2.5)
*1 Assuming the use of bare wiring (without rack or duct): 600 V class of vinyl-insulated IV wires for 60°C, 600 V class of
polyethylene-insulated HIV wires for 75°C, and 600 V class of polyethylene-insulated cross-link wires for 90°C.
Notes: 1) A box () in the above table replaces A, C, E, or U depending on shipping destination.
2) A box (
■) in the above table replaces S (Basic type) or E (EMC filter built-in type) depending on the
enclosure.
3) Values in parentheses ( ) in the above table denote wire sizes for the European version.

If environmental requirements such as power supply voltage and ambient temperature differ
from those listed above, select wires suitable for your system by referring to Table 6.1 and
Appendices, App. F "Allowable Current of Insulated Wires."