Fuji Electric Frenic-Mini - Page 106

6-6
Table 6.2 Cont. Wire Size (HP, AWG ratings) (for main circuit power input and inverter output)
Recommended wire size (AWG) at 50°C (122°F) or below
Main circuit power input
[L1/R , L2/S , L3/T] or [L1/L, L2/N]
w/ DC reactor (DCR) w/o DC reactor (DCR)
Inverter output [U , V , W]
Allowable temp.*1 Allowable temp.*1 Allowable temp.*1
Power
supply
voltage
Applicable
motor
rating
(HP)
Inverter type
140°F 167°F 194°F
Current
(A)
140°F 167°F 194°F
Current
(A)
140°F 167°F 194°F
Current
(A)
1/8 FRN0001C2S-2 0.57 1.1 0.8
1/4 FRN0002C2S-2 0.93 1.8 1.5
1/2 FRN0004C2S-2 1.6 3.1 3.0
1 FRN0006C2S-2 3.0 5.3 5.5
2 FRN0010C2S-2 5.7 9.5 8.0
3 FRN0012C2S-2 8.3
14
13.2
14
11
5 FRN0020C2S-2
14
14.0 10
14 14
22.2 12
14
17
7.5 FRN0025C2S-2 10
14
21.1 8 12 12 31.5 10 12
14
25
10 FRN0033C2S-2 8 12
14
28.8 6 10 10 42.7 8 12 12 33
15 FRN0047C2S-2 6 10 10 42.2 4 6 8 60.7 6 8 10 47
Three-
phase
230 V
20 FRN0060C2S-2 4 6 8 57.6 1 4 6 80.1 4 6 8 60
1/2 FRN0002C2-4 0.85 1.7 1.5
1 FRN0004C2-4 1.6 3.1 2.5
2 FRN0005C2-4 3.0 5.9 3.7
3 FRN0007C2-4 4.4 8.2 5.5
5 FRN0011C2-4 7.3
14
13.0 9
7.5 FRN0013C2-4 10.6 12 17.3
14
13
10 FRN0018C2-4
14
14.4 10
14 14
23.2 12 18
15 FRN0024C2-4 10
14
21.1 8 12 12 33.0 10
14
24
Three-
phase
460 V
20 FRN0030C2-4 8 12
14
28.8 6 10 10 43.8 8 12
14
30
1/8 FRN0001C2-7 1.1 1.8 0.8
1/4 FRN0002C2-7 2.0 3.3 1.5
1/2 FRN0004C2-7 3.5 5.4 3.0
1 FRN0006C2-7 6.4
14
9.7 5.0
2 FRN0010C2-7
14
11.7 12
14
16.4 8.0
Single-
phase
230 V
3 FRN0012C2-7 12
14 14
17.5 10 12
14
24.8
14 14 14
11
1/8 FRN0001C2S-6U 2.1 3.5 0.7
1/4 FRN0002C2S-6U 3.8 5.8 1.4
1/2 FRN0003C2S-6U 6.4
14
9.4 2.5
Single-
phase
115 V
1 FRN0005C2S-6U
14 14 14
12.0 12
14 14
16.0
14 14 14
4.2
*1 Assuming the use of bare wiring (without rack or duct): 600 V class of vinyl-insulated IV wires for 60°C (140°F), 600 V
class of polyethylene-insulated HIV wires for 75°C (167°F), and 600 V class of polyethylene-insulated cross-link wires for
90°C (194°F).
Notes: 1) A box () in the above table replaces A, C, E, or U depending on shipping destination.
2) A box (■) in the above table replaces S (Basic type) or E (EMC filter built-in type) depending on the
enclosure.
3) Values in parentheses ( ) in the above table denote wire sizes for the European version.

If environmental requirements such as power supply voltage and ambient temperature differ
from those listed above, select wires suitable for your system by referring to Table 6.1 and
Appendices, App. F "Allowable Current of Insulated Wires."