Fujitsu PRIMERGY RX900 S1 - Page 12

12 Maintenance Manual RX900 S1
Contents
8.9.5 Inserting the expansion card in the slot . . . . . . . . . . . . . 161
8.9.6 Installing the PCI Riser (if applicable) . . . . . . . . . . . . . . 162
8.9.7 Completing the task . . . . . . . . . . . . . . . . . . . . . . . 162
8.10 Replacing the Modular RAID controller . . . . . . . . . . . 163
8.10.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . 163
8.10.2 Starting the task . . . . . . . . . . . . . . . . . . . . . . . . 164
8.10.3 Removing the PCI Riser . . . . . . . . . . . . . . . . . . . . 164
8.10.4 Removing the Modular RAID controller . . . . . . . . . . . . . 165
8.10.5 Inserting the Modular RAID controller . . . . . . . . . . . . . 166
8.10.6 Installing the PCI Riser . . . . . . . . . . . . . . . . . . . . . 168
8.10.7 Completing the task . . . . . . . . . . . . . . . . . . . . . . . 168
8.11 Installing a Battery Backup Unit (BBU) . . . . . . . . . . . 169
8.11.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . 169
8.11.2 Starting the task . . . . . . . . . . . . . . . . . . . . . . . . 170
8.11.3 Connecting the BBU cable to the BBU . . . . . . . . . . . . . 170
8.11.4 Installing the BBU in the BBU holder . . . . . . . . . . . . . . 171
8.11.5 Connecting the BBU to the Modular RAID controller . . . . . . 173
8.11.6 Completing the task . . . . . . . . . . . . . . . . . . . . . . . 174
8.12 Replacing a Battery Backup Unit (BBU) . . . . . . . . . . . 175
8.12.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . 175
8.12.2 Starting the task . . . . . . . . . . . . . . . . . . . . . . . . 176
8.12.3 Disconnecting the BBU from the Modular RAID controller . . . 177
8.12.4 Removing the BBU from the BBU holder . . . . . . . . . . . . 178
8.12.5 Disconnecting the BBU cable from the BBU . . . . . . . . . . 179
8.12.6 Reinstalling a new BBU . . . . . . . . . . . . . . . . . . . . . 179
8.12.7 Completing the task . . . . . . . . . . . . . . . . . . . . . . . 179
9 Main memory . . . . . . . . . . . . . . . . . . . . . . . . . 181
9.1 Installing a CPUMEMR . . . . . . . . . . . . . . . . . . . . 183
9.1.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . 183
9.1.2 Starting the task . . . . . . . . . . . . . . . . . . . . . . . . 183
9.1.3 Populating the CPUMEMR . . . . . . . . . . . . . . . . . . . 184
9.1.4 Selecting the CPUMEMR slot . . . . . . . . . . . . . . . . . . 184
9.1.5 Removing the air duct (if applicable) . . . . . . . . . . . . . . 185
9.1.6 Inserting the CPUMEMR in the slot . . . . . . . . . . . . . . . 186
9.1.7 Inserting the air duct in the slot (if applicable) . . . . . . . . . 187
9.1.8 Completing the task . . . . . . . . . . . . . . . . . . . . . . . 187
9.2 Replacing a faulty CPUMEMR . . . . . . . . . . . . . . . . 188