GE LOGIQ 400 - Page 179

GE MEDICAL SYSTEMS
2127661
LOGIQ 400 SERVICE MANUAL

RENEWAL PARTS
6–49
REV 9
OPERATOR CONSOLE ASSY
2127794 – 2127803 : V2.11
2164514 – 2164523 : V3.00
2180828 – 2180837 : V3.10
2212968 – 2212977 : V3.40
2239789, 2239793 – 2239799, 2239804, 2239805 : V4.01
2250251, 2250253 – 2250256, 2250258 – 2250267 : V4.31
2264467 – 2264472, 2264475, 2265935 – 2265941 : V5.01
2197064, 2198442 – 2198445 : LOGIQ 400CL, V3.20
2213911 – 2213915 : LOGIQ 400CL, V3.41
2239832 – 2239836 : LOGIQ 400CL, V4.02
2250270, 2250271, 2255918, 2255919 : LOGIQ 400CL, V4.32
2265944 – 2265947 : LOGIQ 400CL, V5.01
MATERIAL LIST (8/12)
SECTION
PART NAME PART NO. QTY. DESCRIPTION FOR
REFERENCE
FRONT, UPPER & LEFT BLOCK
511 NEST FAN ASSY 2117028 1 1 6–2–67
NEST FAN ASSY 2265556 1 1 From V5 System 6–2–67
512 PROBE CONN SET ASSY 2128723 1 1 For 3 slots model 6–2–68
PROBE CONN SET ASSY 2268527 1 1 From V5 System 6–2–68
513 PROBE CONN SET ASSY 2117027 1 1 For 2 slots model 6–2–68
PROBE CONN SET ASSY 2117027–2 1 1 6–2–68
PROBE CONN SET ASSY 2265572 1 1 From V5 System 6–2–68
514 CONNECTOR COVER U0477FD 1 2 6–2–69
515 SHIELD FINGER LONG P9524DW 1 1 6–2–70
516 SHIELD FINGER SHORT P9524DX 1 1 6–2–70
517 PROBE CONN 1 ASSY 2231575 1 2 For 3 slots model 6–2–71
518 DCON ASSY 2123321 1 2 For 2 slots model 6–2–71
519 PRAG ASSY 2123323 1 2 6–2–72
520 MODD U0052ZA 1 1 6–2–73
MODD 2187012 1 1 Refer to Note below: 6–2–73
MODD 2187012–2 1 1 Refer to Note below: 6–2–73
521 MODD FAN 2122998–2 1 1 6–2–73
522 MODD HOLDER ASSY 2117029–2 1 2 including MODD Fan (521) 6–2–73
FRU
NO.
FRU
blinds one slot for 2 slots
models
From software V3.00
console. This Assy has
backward compatibility
with old Assy (2117027)
Note
The folding method of CB24A (or CB24N) cable is different between the case of using the old MODD
(U0052ZA) and the case of using the new MODD (2187012 and 2187012–2). For more details re-
garding the folding cable, refer to 6–6–4.
Note
The appearance of new MODD (2187012–2) is different from the old one (2187012). The old MODD
(2187012) can be replaced with new one (2187012–2). For the settings of the DIP switches and the
jumper switches, refer to 6–2–73.