GRAPHTEC FCX2000

To Next Page

To Previous Page

FCX2000-UM-251-9370 8-9

8 DISASSEMBLY AND ASSEMBLY

(7) Detach the rear bottom cover as shown in the picture below.

(8) Detach the X exible cable from the rear bottom cover.

How to reinstall the Rear Bottom Cover

(1) Reattach the rear bottom cover in the reverse order in which it was detached.

Main Page

Table of Contents4
Introduction10
Model Names And Basic Specifications10
Standard Accessories10
Main Specifications12
External Dimensions13
Regarding The Blower (Vacuum Pump)15
Setup Procedure16
Installation Space16
Unpacking17
Take Out The Stand Parts From The Box17
Assembling The Stand20
Installing The Main Unit Onto The Stand21
Take Out The Main Unit From The Box21
Removing The Packing Material From The Main Unit23
Confirming The Conditions Of X Flexible Cable24
Installing The Roll Media Stocker25
Installing The Warning Light Option26
Installing The Warning Light Option Oph-A4027
Installing The Warning Light Option Oph-A4129
Installing The Warning Light Option Oph-A4234
Description Of Parts41
Plotter Nomenclature41
Cutter Plunger43
Basic Operation44
How To Use The Control Panel44
Menu Tree48
Replacing The Cutter Blade55
Adjusting The Blade Length56
Attaching A Tool57
Adjusting The Tool Carriage Height58
About The Initial Setup Screen59
Selecting Tool Condition60
Selecting The Tool Condition Number60
Setting The Tool Condition62
Running Cutting Tests66
Cutting Test66
Confirm The Results Of The Cutting Test68
Daily Maintenance70
Storing The Plotter70
Cleaning The Cutter Pen70
Recommended Parts List72
List Of Tools74
Tools74
Disassembly And Assembly76
Outer Part76
Right Front Corner Cover76
Right Rear Corner Cover76
Left Front Corner Cover77
Left Rear Corner Cover77
Right Top Cover78
Left Top Cover78
Right Side Cover79
Left Side Cover80
How To Open The Front Bottom Cover80
Front Top Cover81
Rear Top Cover82
Rear Bottom Cover83
Y Bar Cover85
Pen Block Cover86
Front Y Bar End Cover87
Rear Y Bar End Cover87
How To Open The Control Box88
X-Axis Drive Part89
Motor89
Motor Belt91
Front X Belt93
Rear X Belt96
Home Sensor Board99
Flexible Cable100
Y-Axis Drive Part104
Y Motor104
Y Motor Belt106
Y Home Sensor Board108
Y Relay Board109
Pen Board110
Pen Block111
Registration Sensor Boards113
Y Flexible Cable114
Y Belt116
Belt Tension & Gear Adjustment118
Adjusting The X Motor Belt Tension118
Adjusting The Y Motor Belt Tension119
Adjusting The Front X Belt Tension120
Adjusting The Rear X Belt Tension122
Adjusting The Y Belt Tension124
Adjusting The Play Of X Motor Drive Gear126
Adjusting The Play Of Y Motor Drive Gear128
Control Box129
Main Board129
Power Supply Board130
Fan131
Control Panel132
Control Panel Board132
Lcd135
Control Panel Keys135
Electrostatic Adhesion Part (Fcx2000-120Es Only)136
High Voltage Board136
Electrostatic Relay Board137
Replacing The Writing Panel138
Replacing The Electrostatic Adhesion Panel (Fcx2000-120ES)138
Replacing The VC Panel143
Adjusting The Y Bar Height144
Adjusting The Y Bar Right Angle Precision146
Electrical Adjustments147
List Of Items Requiring Readjustment147
Flowchart Of The Adjustment Sequence148
The Main Board Was Replaced (Normal Procedure)148
The Main Board was Replaced (if the Adjustment Values Could Not Copy from the SUB-NVRAM.)149
The Pen Block Was Replaced150
The X Home Sensor Was Replaced150
The Y Home Sensor Was Replaced150
The Registration Mark Sensor Was Replaced150
The X Or Y Motor Was Replaced151
The X Or Y Belt Was Replaced151
Location Of The Boards152
Explanation Of The Values Of The Main Board153
Setting The Dip Switches154
Updating The System Firmware155
Clearing The Nv-RAM157
Selecting Display Language & Length Unit159
Copying The Adjustment Value Form The Sub-NVRAM160
Adjusting The Home Position162
Adjusting The Pen Force165
Adjusting The Distance And The Perpendicularity Accuracy169
Adjusting The Tool Interval174
Adjusting The Registration Mark Sensor Sensitivity178
Adjusting The Offset Of Registration Mark Sensor180
Back Up To The Sub-NVRAM184
Testing The Control Panel Keys And Home Sensors186
About Start Up Mode187
Troubleshooting189
The Power Is Not Turned On189
When It Does Not Work Rightly190
The Cutting Result Is Not Good194
Error Messages In Gp-Gl Command Mode196
Error Messages In Hp-Gl Command Mode197
Arms Error Messages199
Hardware Errors203
Operational Error207
Caution Message208
Self Diagnostic Test209
Parts Lists211
Main Outer211
Main Frame213
Control Box215
Control Panel216
Y Bar Outer217
Y Bar Part218
Pen Block220
Writing Panel222
Wiring Harness223
Stand224
Media Hanger225
Warning Light Option226
Standard Accessories227
Block Diagrams And Circuit Diagrams228
Block Diagram228
Main Board (Pn4031-01)229
Control Panel Board (Pn4031-02)242
Y Relay Board (Pn4031-03)243
Pen Relay Board (Pn4031-04)244
Home Sensor Board (Pn4031-05)245
Registration Sensor Board (Pn4031-07)245
Y Registration Sensor Board (Pn4031-08)245
Usb Relay Board (Pn4031-09)246
High Voltage Board (Pn4031-10)246
High Voltage Relay Board (Pn4031-15)247

GRAPHTEC FCX2000 - Page 84

Table of Contents

Related product manuals