GSi AUDERA PRO - SPL to HL Conversion Table

To Next Page

To Previous Page

GSI Audera Pro User Manual

D-0129360 Rev A Page 72 of 231

SPL to HL Conversion Table

The SPL to HL button will be available for the Click and Tone Burst stimulus types. A

password is required to enter the SPL to HL Table.

The values correspond to HL conversion.

Main Page

Table of Contents3
Preface12
- Manual Conventions12
- Regulatory Symbols13
- Device Symbols15
Warnings and Cautions16
- Important Safety Instructions16
- Safety Precautions16
- Explosion19
- Environmental Factors19
- Electromagnetic Compatibility (EMC) Considerations19
- Ambient Noise20
  - Maximum Ambient Noise20
  - Transducer Sound Attenuation21
Introduction22
- Indications for Use22
- Contraindications22
- Modalities24
Unpacking the System26
- Standard Components26
- Optional Components27
Getting Started28
- Components28
- System Assembly28
- Base Unit Rear Panel30
  - Connections30
- Software Installation31
- Operating Audera Pro33
  - Launching Audera Pro Software33
Opening Window34
- Menu Options35
- Opening Window Toolbar36
  - Connection Status37
- Password37
- Testing37
- Hardware Setup38
- Normative Data40
  - Menu Options40
- Operators41
- System Log42
Patient Information Management44
- New Patient44
  - Patient Information Function Buttons45
- Open Patient46
- Edit Patient48
- Backup Patient Data49
Evoked Potentials (EP)50
- Title Bar50
- EP Main Menu51
  - Patient51
  - Protocol51
  - Stimulus52
  - Amplifier52
  - Recordings53
  - Averaging54
  - Process54
  - Display55
  - Report57
  - Print58
  - Help58
- Information Bar59
- Toolbar60
- EP Waveform Area62
- Page Selection Control62
- Side Toolbar62
- EEG Panel63
- Collection Toolbar64
  - Window and Sample Rate66
- Automated Protocol Dialog67
- Stimulus Dialog69
  - Calibration Table73
  - SPL to HL Conversion Table74
  - File Calibration Table75
  - Stimulus Display Dialog76
- P300/MMN Setup Dialog77
- Amplifier Settings Dialog78
- External Trigger81
- Remote Impedance Display Box82
- Data Analysis84
- Data Files Dialog84
  - Data Pages85
  - Display Options86
  - Cursors89
- Waveforms90
  - Labeling Peaks91
  - Default Labels92
  - SP/AP Ratio93
  - MMN Area94
  - Waveform Options95
  - Record Info98
- Post-Acquisition Processing99
  - Calculating Bayesian Weighted Average99
  - Adding and Subtracting Waveforms99
  - Comparing Recordings99
  - Inverting a Waveform100
  - Filtering100
  - Cross-Correlation101
  - Split Active Recording101
  - Latency Intensity Graph101
- Reports102
  - Adding Information103
  - Printing Options103
  - Report Header and Adding a Logo to the Report103
- Keyboard Shortcuts104
- Typical EP Evaluation Workflow105
Vemp Analysis Module106
- Open Records106
- VEMP Analysis Window107
- VEMP Analysis Menu108
- VEMP Analysis Toolbar110
- VEMP Culling Mode View110
- VEMP Calculation Mode View112
Auditory Steady-State Response (ASSR)114
- Title Bar114
- ASSR Main Menu115
- Information Bar120
- Toolbar121
- ASSR Waveform Area123
- Page Selection Control123
- Side Toolbar123
- EEG Panel124
- Stimulus Information Panel125
- Amplifier Settings Dialog126
- Collection Toolbar129
- Automated Protocol Dialog130
- Signal to Noise Ratio and Noise Graphs131
- Keyboard Shortcuts131
- Data Analysis132
- Data Files Dialog132
- Analyze Active Wave133
- ASSR Response Audiogram136
- HL Correction Table138
Distortion Products Otoacoustic Emissions (DPOAE)140
- Title Bar140
- DPOAE Main Menu141
- Toolbar142
- Data Collection143
- Data Analysis160
- Dp I/O165
Transient Evoked Otoacoustic Emissions (TEOAE)169
- Title Bar169
- TEOAE Main Menu170
- Information Bar174
- Toolbar174
- TE Waveform Area176
- Page Selection Control176
- Side Toolbar176
- Meatal Response Panel177
- Collection Toolbar177
- Data Collection178
- Passing Criteria179
- Data Analysis180
- Data Files Dialog180
- Reports186
  - Adding Information186
  - Printing Options186
Cleaning and Maintenance188
- Cleaning188
- Maintenance191
  - Operational Checks191
  - Calibration and Safety Checks191
Cybersecurity192
Troubleshooting195
- Error Messages195
- Loopback Test Cable198
Supplies and Accessories201
- OAE Probe Ear Tips - Single Use - Sanibel ADI Silicone202
- Appendix A - Default Settings204
- Default EP Settings204
- VEMP Settings205
- Default ASSR Settings206
- Default DPOAE Settings207
- Default TEOAE Settings208
- File Naming209
  - Recording Naming Convention209
Appendixa - Default Settings204
Appendix B - Technical Data210
Appendix C - Transducer Reference Equivalent Threshold Levels and Maximum Output214
Level214
- Transducer Reference Equivalent Threshold Levels Table215
- Transducer Reference Equivalent Threshold Levels Table Notes216
- Maximum Output Levels217
Appendix D - Specification of Input/Output Connections221
- Bone Oscillator221
- Headphones/Inserts (2 Connectors, R, L)221
- Mains Cable221
- OAE Probe221
- Patient Electrode Cable221
- Digital I/O223
- Speakers (R, L)223
- Usb223
- Appendix E - Warranty and Repair224
- Repair224
- Warranty224
Appendixe - Warranty and Repair224
Appendixf - Recycling and Disposal226
- Appendix F - Recycling and Disposal227
- Appendix G - Electromagnetic Compatibility (EMC)227
- Cautions Regarding EMC227
- Guidance and Manufacturer's Declaration Electromagnetic Emissions228
- Communications Equipment229
- Recommended Separation Distances between Portable and Mobile RF229
- Guidance and Manufacturer's Declaration Electromagnetic Immunity230
Appendixg - Electromagnetic Compatibility (Emc)227

Related product manuals

GSi AUDERA PRO - SPL to HL Conversion Table

Table of Contents

Related product manuals