GW Instek PEL-3000 Series - PEL-3000(H) Specifications

257 pages

To Next Page

To Previous Page

PEL-3000(H) User Manual

232

PEL-3111H

PEL-3211H

Booster Pack

Main Page

Table of Contents3
Safety Instructions5
Getting Started9
PEL-3000(H) Series Introduction11
Model Line up11
Main Features12
Accessories13
Package Contents15
Appearance16
Front Panel16
Pel-3021/ Pel-304116
Pel-3021H/ Pel-3041H17
Pel-311117
Pel-3111H18
PEL-3211(H) Booster Pack18
Rear Panel22
Pel-3021/ Pel-304122
Pel-3021H/ Pel-3041H23
Pel-311123
Pel-3111H24
PEL-3211 Booster Pack24
PEL-3211H Booster Pack24
Display27
First Time Use Instructions28
Rack Mount Kits28
Power up and Self Test30
Load Default Settings31
Setting the Date and Time31
Load Wiring32
Load Wire Connections35
Using the Front Panel Input Terminals36
Using the Rear Panel Input Terminals37
Using the Terminal Cover (PEL-011)38
Using the Terminal Cover (PEL-013)40
Using the Terminal Cover42
Using the Monitor out Cover (Only for PEL-3021H, PEL-3041H, PEL-3111H)43
Remote Sense44
Firmware Update45
Conventions47
Help Menu52
Operation53
Basic Operation55
CC Mode55
CR Mode57
CR Units58
CV Mode59
CP Mode60
CV Mode62
Turning on the Load63
Shorting the Load63
Safety Short64
Short Key Configuration65
Short Function Enable/Disable66
Locking the Front Panel Controls66
Basic Configuration67
Select the Switching Function67
Select the Display Units for Dynamic Mode Levels69
Select the Switching Time Configuration for Dynamic Mode70
Slew Rate71
CV, +CV Mode Response Speed72
CC, CR and CP Mode Response Speed73
Advanced Configuration Settings74
Soft Start74
Von Voltage Settings75
Von Voltage75
Von Latch76
Von Delay77
Timer Functions77
Count Time77
Cut off Time78
Auto Load Configuration79
Load off (Mode) and Load off (Range)80
Step Resolution Configuration81
Cursor Mode Configuration81
Step Mode Configuration82
Protection Settings84
Ocp84
Opp85
Uvp86
UVP Ring Time87
Ovp89
Unreg90
Para91
Rvp92
System Settings93
Sound Settings93
Speaker Settings93
Alarm Tone Settings94
Display Settings94
Contrast and Brightness94
Control Settings95
Language Settings95
Input/Output Trigger Settings95
Trigger in Delay95
Trigger out Width96
Measure Average96
Go-Nogo97
Setting the Go-Nogo Limits97
Running a Go-Nogo Test98
Save Recall100
File Structure100
File Types101
Saving Files to Internal Memory102
Saving Files to USB Memory104
Recalling Files from Internal Memory106
Recalling Files from USB Memory107
Recall Memory Safety Setting109
File Utility109
Preset111
Quick Preset Save111
Quick Preset Recall111
Default Settings112
Factory Default Settings112
User's Default Setting112
Function Menu113
Function Menu Overview114
Select a Function114
Turning on the Load with the Selected Function116
Complete Ring Time117
NSEQ Timer118
Program120
Program Overview120
Create a Program122
Create a Program Chain125
Running a Program or Chain126
Sequence128
Normal Sequence Overview128
Timing Edit Configuration132
Data Edit Configuration134
Running a Normal Sequence135
Fast Sequence Overview138
Timing Edit Configuration142
Data Edit Configuration143
Running a Fast Sequence145
OCP Test Automation147
OPP Test Automation153
BATT Test Automation159
External Control167
Analog Control168
J1 Connector Overview168
J3 Port (PEL-3021H/PEL-3041H/PEL-3111H)169
External Voltage Control - Overview170
External Voltage Control - Operation171
Adjust Offset and Full Scale with Variable Resistor (PEL-3021H/ PEL-3041H/ PEL-3111H)173
External Resistance Control - Overview175
External Resistance Control - Operation176
Adjust Offset and Full Scale with Variable Resistor (PEL-3021H/ PEL-3041H/ PEL-3111H)179
Turning the Load on Using External Control180
Load On/Off Status182
External Control of the Range182
I Range Status183
External Trigger Signal185
External Control of the Alarm185
Alarm Status186
Short Control186
Monitor Signal Output187
Trigger Signal Output187
Current Monitor Output188
Voltage Monitor Output (PEL-3021H/PEL-3041H/PEL-3111H)189
Parallel Operation190
Parallel Capacity, PEL-3021, PEL-3041, PEL-3111190
Parallel Capacity, PEL-3021H, PEL-3041H, PEL-3111H191
Parallel Capacity, PEL-3211191
Parallel Capacity, PEL-3211H192
Connection192
Configuration194
Turning the Load on196
Disable Parallel Mode196
Remote Control197
Interface Configuration198
Configure to USB Remote Interface198
Configure GPIB Interface198
Configure RS232C200
RS232C/USB Remote Control Function Check201
Using Realterm to Establish a Remote Connection202
GPIB Function Check205
Faq208
Appendix211
Replacing the Dust Filter212
Replace the Clock Battery213
GPIB Installation214
PEL-3000(H) Default Settings215
Frame Control Connector Contacts218
J1 Connector218
Operating Mode Description220
J2 Connector220
Monitor out Ports J3 (PEL-3021H/PEL-3041H/PEL-3111H)221
J1 Connector Booster221
J2 Connector Booster222
Operating Mode Description224
CC Mode224
CR Mode225
CP Mode227
CV Mode228
Operating Area229
PEL-3000(H) Specifications236
Rating (Master / Slave)236
Rating (Booster / Slave)236
CC Mode237
CR Mode238
CV Mode239
CP Mode239
Slew Rate240
Meter241
Dynamic Mode242
Soft Start245
Remote Sensing245
Protection Function245
Sequence246
Other246
Analog External Control247
Front Panel BNC Connector248
General248
PEL-3000(H) Dimensions250
Pel-3111250
Pel-3021, Pel-3041251
Pel-3211252
Declaration of Conformity253
Index255

GW Instek PEL-3000 Series - PEL-3000(H) Specifications

Table of Contents

Other manuals for GW Instek PEL-3000 Series

Related product manuals