88
Macros
96-8000 rev R June 2007
#5001-#5005 Previous block end position
#5021-#5025 Present machine coordinate position
#5041-#5045 Present work coordinate position
#5061-#5065 Present skip signal position - X,Y,Z,A,B
#5081-#5085 Present tool offset
#5201-#5205 G52 Work Offsets
#5221-#5225 G54 Work Offsets
#5241-#5245 G55 Work Offsets
#5261-#5265 G56 Work Offsets
#5281-#5285 G57 Work Offsets
#5301-#5305 G58 Work Offsets
#5321-#5325 G59 Work Offsets
#5401-#5500 Tool feed timers (seconds)
#5501-#5600 Total tool timers (seconds)
#5601-#5699 Tool life monitor limit
#5701-#5800 Tool life monitor counter
#5801-#5900 Tool load monitor maximum load sensed so far
#5901-#6000 Tool load monitor limit
#6001-#6277 Settings (read only)
#6501-#6999 Parameters (read only)
NOTE: The low order bits of large values will not appear in the macro variables for settings and parameters
#7001-#7006 (#14001-#14006) G110 (G154 P1) additional work offsets
#7021-#7026 (#14021-#14026) G111 (G154 P2) additional work offsets
#7041-#7046 (#14041-#14046) G112 (G154 P3) additional work offsets
#7061-#7066 (#14061-#14066) G113 (G154 P4) additional work offsets
#7081-#7086 (#14081-#14086) G114 (G154 P5) additional work offsets
#7101-#7106 (#14101-#14106) G115 (G154 P6) additional work offsets
#7121-#7126 (#14121-#14126) G116 (G154 P7) additional work offsets
#7141-#7146 (#14141-#14146) G117 (G154 P8) additional work offsets
#7161-#7166 (#14161-#14166) G118 (G154 P9) additional work offsets
#7181-#7186 (#14181-#14186) G119 (G154 P10) additional work offsets
#7201-#7206 (#14201-#14206) G120 (G154 P11) additional work offsets
#7221-#7226 (#14221-#14221) G121 (G154 P12) additional work offsets
#7241-#7246 (#14241-#14246) G122 (G154 P13) additional work offsets
#7261-#7266 (#14261-#14266) G123 (G154 P14) additional work offsets
#7281-#7286 (#14281-#14286) G124 (G154 P15) additional work offsets
#7301-#7306 (#14301-#14306) G125 (G154 P16) additional work offsets
#7321-#7326 (#14321-#14326) G126 (G154 P17) additional work offsets
#7341-#7346 (#14341-#14346) G127 (G154 P18) additional work offsets
#7361-#7366 (#14361-#14366) G128 (G154 P19) additional work offsets
#7381-#7386 (#14381-#14386) G129 (G154 P20) additional work offsets
#7501-#7506 Pallet priority
#7601-#7606 Pallet status
#7701-#7706 Part program numbers assigned to pallets
#7801-#7806 Pallet usage count
#8500 Advanced Tool Management (ATM). Group ID
#8501 ATM. Percent of total available tool life of all tools in the group.
#8502 ATM. Total available tool usage count in the group.
#8503 ATM. Total available tool hole count in the group.
#8504 ATM. Total available tool feed time (in seconds) in the group.
#8505 A
TM. Total available tool total time (in seconds) in the group.
#8510 ATM. Next tool number to be used.
#8511 ATM. Percent of available tool life of the next tool.
To Next Page
Loading...
Need help?
General
